Case IH AFX8010 — LIGHTING SYSTEM

DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Front work light Wiring harness - Testing (A.40.A.16.88 - G.40.A.20) AFX8010 9668 1 27/05/2004 A.40.A / 60 N° Test Point Expected Result Other Result (Possible Cause) 17 Place Key Switch S-02 in ON position. Close Work Light Switch S-43 Measure for 12 volts at Road Lights Relay K-27 (pin 1). 12 volts If good reading, the wiring has good continuity. Go to test 18 Road lights Relay K-27. Adjacent circuits. Go to test 18 18 Measure the voltage at Road Lights Relay K-27 (pin 1). 12 volts If good reading, Go to test 19 Open or short circuit 117 between Road Lights Relay K-27 (pin 1) and CCM-1 (pin j1-5). See Service Manual for testing of CCM.

19 Measure for 12 volts at Road Lights Relay K-27 (pin 3). 12 volts If good reading, Go to test 20 Open circuit 60 (RD) between Distance Work Lights Relay K-21 (pin 3) and Fuse #29. Short to ground on circuit 21 (PU) between Distance Work Lights Relay K-21 (pin 5) and Road Lights Relay K-27 (pin 3). A short will cause Fuse #29 to blow. 20 Measure for 12 volts at Road Lights Relay K-27 (pin 4). Measure the resistance in circuit 119 (PU) between Light Control Relay K-02 (pin 4) and Road Lights Relay K-27 (pin 4) and ground. 12 volts If good reading; Go to test 21 Open circuit 119 (PU) between Light Control Relay K-02 (pin 4) and Road Lights Relay K-27 (pin 4).

21 Disconnect the Road Lights Relay K-27. Measure the resistance in circuit 158 (BK) between Road Lights Relay K-27 (pin 2) and ground. Less than 1 ohms. If good reading, replace Road Lights Relay K-27. Open circuit 158 (BK) between Road Lights Relay K-27 (pin 2) and ground. N° Test Point Expected Result Other Result (Possible Cause) 1 Place Key Switch S-02 in .ON. position. Close Work Light Switch S-43. Measure for 12 volts at (pin 5). 12 volts. If good reading, Go to test 2 Perform Lower Work Lights Relay Test. 2 Measure for 12 volts at Grain Tank Light E-30 connector X108 (pin A).

12 volts If good reading, Go to test 3 Open circuit 65 (PU) or 646 (PU) between Lower Work Lights Relay K-30 (pin 5) and Grain Tank Light E-30 connector X108 (pin A). 3 Disconnect the Grain Tank Light E-30. Measure the resistance on circuit 681 (BK) between Grain Tank Light E-30 connector X108 (pin B) and ground. Less than 1 ohms. If good reading, replace the Grain Tank Light E-30 bulb. Open in circuit 681 (BK) between Grain Tank Light E-30 connector X108 (pin B) and ground. 4 Place Key Switch S-02 in ON position. Close Work Light Switch S-43. Measure for 12 volts at Lower Work Light Relay K-30 (pin 5). 12 volts. If good reading, Go to test 5 Perform Lower Work Lights Relay Test.

5 Measure for 12 volts at LH Lower Work Light E-23 connector X163 (pin A). 12 volts If good reading, Go to test 6 Open circuit 65 (PU) or 644 (PU) between Lower Work Lights Relay K-30 (pin 5) and LH Lower Work Light E-23 connector X163 (pin A).