DISTRIBUTION SYSTEMS - LIGHTING SYSTEM A. If 12 volts is not present, there is an open circuit in the cab main (CM) harness or cab roof (CR) harness between connector X015 pin J1-11 through connector X002 pin 18 to connector X133 pin B on wires 231 purple or 232 purple. Locate the open and repair. 5. Turn the key switch to the "OFF" position. Use a multimeter to check for continuity between connector X133 pin A and chassis ground. There should be no continuity, or very high continuity to ground, depending on the type of multimeter used.. B. If 12 volts is present, continue with step 5 . A.
If there is continuity to ground, there is a short to ground in the cab roof (CR) harness between connector X133 pin A and connector X138 pin 1 wire 175 purple to the console light E-35.Locate the short and repair. B. If there is no continuity to ground, continue with step 6 . 6. Turn the key switch to the "OFF" position. Use a multimeter to check for continuity between connector X133 pin C and chassis ground. There should be no continuity, or very high continuity to ground, depending on the type of multimeter used.. A.
If there is continuity to ground, there is a short to ground in the cab roof (CR) harness between connector X133 pin C and connector X131 pin 7 wire 233 purple to the rear work lights switch S-44.Locate the short and repair. B. If there is no continuity to ground, continue with step 7 . 7. Turn the key switch to the "OFF" position. Use a multimeter to check for continuity between connector X133 pin D and chassis ground. There should be no continuity, or very high continuity to ground, depending on the type of multimeter used.. A.
If there is continuity to ground, there is a short to ground in the cab roof (CR) harness between connector X133 pin D and connector X132 pin 7 wire 235 purple to the work lights switch S-43.Locate the short and repair. B. If there is no continuity to ground, continue with step 8 . 8. Turn the key switch to the "OFF" position. Use a multimeter to check for continuity between connector X133 pin E and chassis ground. There should be no continuity, or very high continuity to ground, depending on the type of multimeter used.. A.
If there is continuity to ground, there is a short to ground in the cab roof (CR) harness between connector X133 pin E and connector X135 pin 7 wire 273 purple to the wiper switch S-20.Locate the short and repair. B. If there is no continuity to ground, continue with step 9 . 9. Turn the key switch to the "OFF" position. Use a multimeter to check for continuity between connector X133 pin F and chassis ground. There should be no continuity, or very high continuity to ground, depending on the type of multimeter used.. A.
If there is continuity to ground, there is a short to ground in the cab roof (CR) harness between connector X133 pin F and connector X130 pin 7 wire 283 purple to the beacon light switch S-41.Locate the short and repair. B. If there is no continuity to ground, continue with step 10 . 10. Turn the key switch to the "OFF" position. Use a multimeter to check for continuity between connector X133 pin G and chassis ground. There should be no continuity, or very high continuity to ground, depending on the type of multimeter used.. A.
If there is continuity to ground, there is a short to ground in the cab roof (CR) harness between connector X133 pin G and connector X125 pin 7 wire 284 purple to the tank extensions switch S-42.Locate the short and repair. B. If there is no continuity to ground, continue with step 11 . 11. Turn the key switch to the "OFF" position. Use a multimeter to check for continuity between connector X133 pin H and chassis ground. There should be no continuity, or very high continuity to ground, depending on the type of multimeter used.. 9668 1 27/05/2004 A.40.A / 83