Caterpillar — Caterpillar C11 and C13 Industrial Engines Operation and Maintenance Manual

SEBU7901-01 57 Maintenance Section Cooling System Coolant (DEAC) - Change 5. Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, “Torque Specifications” for more general information on the proper torques.

5. Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the drain valve (if equipped) or remove the cooling system drain plugs. Allow the water to drain. Flush the cooling system with clean water. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques. Refer to the Specifications, SENR3130, “Torque Specifications” for more general information on the proper torques.

Cooling Systems with Heavy Deposits or Plugging Fill Refer to the Operation and Maintenance Manual, “Refill Capacities and Recommendations” topic for the capacity of the engine’s system and for coolant recommendations. Note: For the following procedure to be effective, there must be some active flow through the cooling system components. 1. Flush the cooling system with clean water in order to remove any debris. Engines that are Equipped with a Coolant Recovery Tank 2. Close the drain valve (if equipped). Clean the drain plugs. Install the drain plugs. Refer to the Specifications Manual for your particular engine for more specific information on the proper torques.

Refer to the Specifications, SENR3130, “Torque Specifications” for more general information on the proper torques. NOTICE Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks. 1. Fill the cooling system with coolant/antifreeze. Refer to the Operation and Maintenance Manual, “Refill Capacities and Recommendations” topic (Maintenance Section) for more information on cooling system specifications. Do not install the cooling system filler cap. NOTICE Fill the cooling system no faster than 19 L (5 US gal) per minute to avoid air locks. 2. Start the engine and run the engine at low idle. Increase the engine rpm to high idle.

Run the engine at high idle for one minute in order to purge the air from the cavities of the engine block. Stop the engine. 3. Fill the cooling system with a mixture of clean water and Caterpillar Fast Acting Cooling System Cleaner. Add .5 L (1 pint) of cleaner per 3.8 to 7.6 L (1 to 2 US gal) of the cooling system capacity. Install the cooling system filler cap. 4. Start the engine and run the engine at low idle for a minimum of 90 minutes. The coolant temperature should be at least 82 °C (180 °F). 3. Add coolant to the cooling system until the cooling system is full. 4. Clean the cooling system filler cap. Inspect the gasket that is on the cooling system filler cap.

If the gasket that is on the cooling system filler cap is damaged, discard the old cooling system filler cap and install a new cooling system filler cap. If the gasket that is on the cooling system filler cap is not damaged, perform a pressure test. A 9S-8140 Pressurizing Pump is used to perform the pressure test. The correct pressure for the cooling system filler cap is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap. NOTICE Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal com- ponents.

To avoid damage to the cooling system, make sure to completely flush the cooling system with clear wa- ter. Continue to flush the system until all signs of the cleaning agent are gone.