Perkins — Perkins 4.108 4.107 4.99 Diesel Engine Workshop Manual

SECTION Q Electrical Equipment ALTERNATOR (d) Remove any dirt accumulated on the regulator/ control box housing, and ensure that cooling air can pass freely over the casing. Models AC5, HAC, 15ACR and 17 ACR 1. Precautions The AC 5 alternator is so designed that a flow of current indicated either by the extinguishing of the warning light, or as shown on the ammeter, is suffiicient evidence that the system is in proper working order. Therefore, no open circuit, voltage or current output checks should be performed in the installation UN- LESS:- 3.

Fault Finding on AC5 The diodes in the alternator function as one-way· valves and the transistors in the regulator/control box operate as fast switches. Both are accurate and sensitive. They do not wear out and seldom require adjustment, but because they are sensitive to voltage changes and high temperature, the following precautions are vital to prevent them from being destroyed. (a) The warning light fails to illuminate when the generator is stationary, and the switch is closed OR fails to become extinguished when the alter- nator is running. (a) DO NOT disconnect the battery whilst the engine is running.

This will cause a voltage surge in the alternator charging system that will immediately ruin the diodes or transistors. (b) No charging current is shown on ammeter. (b) DO NOT disconnect a lead without first stopping the engine and turning all electrical switches to the off position. (c) The battery is flat. (d) The battery is "boiling", indicating loss of voltage control. (c) DO NOT cause a short circuit by connecting leads to incorrect terminals. Always identify a lead to its correct terminal. A short circuit or wrong con- nection giving reverse polarity will immediately and permanently ruin transistors or diodes.

If any of the above symptoms occur, the procedure in- dicated below should be followed. (a) Connect a good quality moving coil voltmeter 0-50 volts range across the battery or regulator negative terminal, and one of the three positive terminals marked LO, MED, HI. Disconnect alter- nator output terminal. Fit a good quality moving coil 0 - 100 amp ammeter in series with the alternator terminal and output lead. The battery should be in a charged condition. (d) DO NOT connect a battery into the system without checking for correct polarity and voltage. (e) DO NOT "flash" connections to check for current flow. No matter how brief the contact the tran- sistors may be ruined.

(b) Close the warning light switch (master electric switch on dashboard) when the warning lamp should light up. 2. Maintenance (c) Switch on a 10-15 amperes load such as lights, etc. for fifteen minutes. The alternator charging system will normally require very little attention, but it should be kept free from build-up of dirt, and a check made if it fails to keep the battery charged. (d) Start engine and run at fast idle speed with fans, etc, for fifteen minutes. 1. The warning light should go out. (a) Regularly inspect the driving belts for wear and correct tension.

It is important to ensure that all belts on a multiple belt drive have equal tension and are each carrying their share of the load. Slack belts will wear rapidly and cause slip which will not drive the alternator at the required speed. Drive belts which are too tight impose severe side thrust on the alternator bearings and shorten their life. Periodically ensure that the alternator is correctly aligned to the drive. 2. The ammeter records a small charge depen- dant on engine speed. (e) Increase engine speed momentarily to maximum speed, when the charging current should be about 30 Amperes for 24 Volt, and 53 Amperes for 12 volt systems.

(f) With the alternator running at approximately half speed, (engine speed about 1,500 rev/min) switch off electrical load. Depending on the connection selected for the positive sensing wire LO; MED or HI, the voltage should rise to between 26 and 28 volts on 24 volt systems and 13-14 volts on 12 volt systems and then (emain constant. At the same time the current reading should drop appreciably. (b) Do not replace faulty belts individually in a mUlti- belt system. A complete matched set of drive belts must always be used. (c) Keep the alternator clean with a cloth moistened in kerosene or cleaning fluids. Ensure that ventilation slots and air spaces are clear and unobstructed.