Perkins — Perkins 4.108 4.107 4.99 Diesel Engine Workshop Manual

ELECTRICAL EQUIPMENT -Q.4 Alternator Output Test with Regulator Inoperative Regulator Test The following test assumes the alternator to have been tested and found satisfactory. Withdraw the two-part connector from the alternator, remove the moulded cover (secured by two screws) and link together regulator terminals 'F' and '-'. Disconnect the variable resistor and remove the link bridging regulator terminals 'F' and '-'. Connect an external test circuit to the alternator output terminals as shown in Fig. Q.1.

With the remainder of the test circuit connected as for the alternator output test, start the engine and again run the alternator up to 6,000 rev/min until the ammeter shows an output current of less than 10 amperes. The voltmeter should then give a reading of 14.0 - 14.4 volts. Any appreciable deviation from this (regulating) voltage means that the regulator is not functioning properly and must be replaced. B + + INO '--------iAI------. If the foregoing tests show the alternator and regulator to be satisfactorily performing, disconnect the test cir- cuit and reconnect the alternator terminal connector.

Now connect a low-range voltmeter between the posi- tive terminal of the alternator (the moulded terminal connector is open-ended to faciltate this) and the posi- tive terminal of the battery. Switch on battery load (headlights etc.), start the engine and increase speed until the alternator runs at approximately 6,000 rev/min. Note the voltmeter reading. 0) CD ~--------iVI_------_1I Transfer the voltmeter connections to the negative terminals of alternator and battery and again note the meter reading. If the reading exceeds 0.5 volt on the positive side or 0.25 volt on the negative side, there is a high resistance in the charging circuit which must be traced and remedied. 01 1.

12 volt 2.2 watt Bu Ib 2. 0-40 or 0-60 Ammeter DYNAMO The following information in concerned with the Lucas C40-1 model. Should information be required in con- nection with any other type of dynamo then the rele- vant manufacturer should be contacted. 3. 12 volt Battery 4. 0-20 Voltmeter 5. 0-15 ohm 35 amp Variable Resistor The C40-1 is of extruded yoke construction and is a ventilated type. Holes in each end bracket allow a pulley mounted fan to draw cooling air through the dynamo. Observe carefully the polarity ot battery and alternator terminals - reversed connections will damage the alternator diodes.

Description The variable resistor across the battery terminals must not be left connected for longer than is necessary to carry out the following test. It is a shunt wound, two pole, two brush machine designed to work in conjunction with a compensated voltage control regulator unit. A ball bearing supports the armature at the driving end and a porous bronze bush at the rear supports the commutator end. Start the engine. At 1,500 rev/min (alternator speed), the test circuit bulb should be extinguished. Increase engine speed until the alternator is running at 6,000 rev/min approximately, and adjust the variable resist- ance until the voltmeter reads 14.0 volts.

The ammeter reading should then be approximately equal to the rated output (See previous paragraph). Any appreci- able deviation from this figure will necessitate the alternator being removed from the engine for further examination. The output of the dynamo is controlled by the regulator unit and is dependent on the state of charge of the battery and the loading of the electrical equipment in use. When the battery is in a low state of charge, the dynamo gives a high output, whereas if the battery is fully charged, the dynamo gives only sufficient output to keep the battery in good condition without any possibility of overcharging.

An increase in output is given to balance the current taken by lamps and other accessories when in use. Failure of one or more of the diodes will be indicated in the above test by effect on alternator output, and also in some instances by abnormally high alternator temperature and noise level. When fitting a new control box, it is important to use only an authorised replacement. An incorrect replace- ment can result in damage to the dynamo.