ELECTRICAL EQUIPMENT-Q.7 NOTE: This is applicable to a brush when half the available wearing length has been worn away. 3. The commutator must be clean and have a polished appearance. If necessary, clean It by pressing a fine dry cloth agaiinst it whilst the armature is turned by hand. If the commutator is very dirty, moisten the cloth with petrol. 4. Keep all the electrical connections clean and tight. Check first that the circuit up to the supply ter- minal on the starter motor is in order. If no voltage is indicated. check the circuit from the battery to the motor via the starter switch. Ensure that all the connections are clean and tight.
If the switch is found to be faulty fit a ser- viceable replacement. Any which have become dirty should be cleaned and the contacting surfaces lightly smeared with petroleum jelly. A normal voltage supply reaching the starter motor terminal indicates that the starter motor has an in- ternal fault and must be removed for examination. If the starter motor operates but does not crank the engine, the starier drive may require cleaning or may have developed some other fault. In either case the starter motor requires removal from the engine for a full examination. "S' TYPE STARTER DRIVE ASSEMBLY (a) Operation This drive incorporates a protective feature known as the 'Run-off Helix'.
The purpose of this feature is to prevent possible damage occuring to the starter motor through excessive torque being applied while the pinion is in engagement, as would arise for example in the event of an engine back-fire during starting. Under normal conditions of engagement, axial move- ment of the pinion is arrested when, in th'3 one direc- tion, the first cup washer has fully compressed the re- straining spring and is abutted hard against the second cup washer and, in the opposite direction, the helically screwed sleeve is pressing the thrust washer hard against the main spring.
In the 'Run-off Helix' drive, the main spring is capable of greater compression than is the equivalent stan- dard 's' pattern drive spring. In addition, the trailing faces of the pinion and helically screwed sleeve are machined to form indented rachet recesses. In the event of a back-fire occuring during starting, the pinion (being able to rotate but incapable of fur- ther axial movement) forces the heiically screwed sleeve along the straight-splines of the starter shaft. This further compresses the main spring and permits axial movement of the screwed sleeve to continue until it is clear of the interior of the pinion.
At this stage, axial movement of the screwed sleeve ceases and the pinion, now jointly supported by the fixed sleeve and the recessed end of the screwed sleeve, is free to be rotated by the engine ring gear. In this way, excessive torque is harmlessly dissipated by the ratchetting action of the pinion and screwed sleeve against the reaction pressure of the main spring. The operation of a 'Run-off Helix' drive can be checked by securing the armature and drive assembly in a vice (using wooden vice-clamps) and applying a torque wrench to the pinion. The rachet action must occur at a torque of not less than 36 Ibf ft (5 kgf m). 06 3.
Servicing (a) Testing in Position If the starter motor does not operate or fails to crank the engine when the starting button is used, switch on the head lamps. When these are not fitted connect a good quality 0-20 voltmeter across the battery ter- minals, operate the starter button and watch for the following symptoms: 1. The headlamps dim (or the voltmeter reading falls appreciably) but the motor does not crank the engine. This may be caused by the starter drive pinion being jammed in mesh with the engine flywheel. The pinion can usually be freed by engaging a low gear and gently rocking the engine.
It is advisable to remove the starter motor from the engine and inspect the starter drive as described later in this section. Sluggish action of the starter motor may be due to a discharged battery, check this by disconnecting the existing cables and reconnecting the motor to a battery known to be fully charged. If the starter motor now functions normally then the battery must be examined. Should the starter motor still not function normally then it should be removed from the engine and examined. 2. The head lamps do not dim (or the voltmeter read- ing remain unaffected) and the motor does not crank the engine.
(b) Routine Maintenance If any difficulty is experienced with the starter motor not meshing correctly with the flywheel, it may be that the drive requires cleaning. The pinion should move freely on the screwed sleeve; if there is any dirty or other foreign matter on the sleeve it must be washed off with paraffin.