John Deere 450H, 550H, 650H — Instrument Panel Functions (Earlier Machines)

Operation—Operator's Station Instrument Panel Functions (Earlier Machines) A—Winch Oil Pressure Indicator—If Equipped: Indicator will light and STOP indicator will light when oil pressure is too low. Immediately stop engine and investigate the problem. G—Hydraulic Oil Filter Restriction Indicator: Indicator will light and stay lit when hydraulic oil temperature is too high. STOP indicator will light and the audible alarm will sound. Immediately park the machine in a safe environment, stop engine and take corrective action. B—Check Service Code Indicator: If indicator stays lit, there is an electrical problem in the transmission control system. It is not necessary to stop the machine.

H—Fasten Seat Belt/Park Lock On Indicator: Indicator will light when key switch is “On” and park lock lever is in up (locked) position. The transmission controller will automatically put the machine in an operational mode that will not harm the engine. I—Transmission Oil Filter Indicator: Indicator will light when transmission filter element is restricted. It is not necessary to stop operation, but the cause should be investigated as soon as possible. The service code that is present is displayed in the transmission controller display window. This service code number pinpoints the problem and is a very important aid for your authorized dealer to quickly diagnose the problem.

Always relay this code number to your dealer when reporting your problem. It is normal for this light to remain lit for several minutes after start-up in cold weather. In extremely cold weather, it is a good practice to operate at reduced engine speed so the light stays off. C—STOP Indicator: J—Voltage Indicator: Indicator will light when battery/alternator is below 12-volts. It is not necessary to stop operation, but the cause should be investigated as soon as possible. IMPORTANT: If STOP indicator flashes and alarm sounds, in most cases stop engine immediately and investigate cause of problem. Do not start engine until problem has been corrected. K—Engine Air Filter Restriction Indicator:

Indicator will light when engine air filter element is restricted. It is not necessary to stop operation, but the cause should be investigated as soon as possible. The STOP indicator flashes and alarm sounds when: Engine oil pressure is too low Transmission oil temperature is excessively high Engine coolant temperature is excessively high L—Fuel Gauge: Gauge will reflect fuel level in tank. Fuel level gauge needle will enter red zone when fuel level in tank is too low. If engine coolant temperature indicator lights indicating that the temperature is excessively high, DO NOT stop engine. Reduce load and run engine at fast idle for several minutes. Stop engine and service machine.

M—Engine Oil Pressure Gauge—If Equipped: After engine is started, gauge needle must point to green zone immediately and not drop into red zone after warm-up. If gauge needle drops into red zone, stop engine. See your authorized dealer. D—Engine Coolant Temperature Indicator: Indicator will light and stay lit when coolant temperature is too high. STOP indicator will light and audible alarm will sound. Immediately take load off he machine and run engine at fast idle for several minutes. If indicator continues to stay on after several minutes of idling, stop engine and take corrective action. N—Engine Coolant Temperature Gauge—If Equipped:

When engine coolant temperature is too high the gauge needle will move to the red zone. Immediately take load off the machine and run engine at fast idle. If gauge needle stays in red zone after several minutes of idling, stop engine. See your authorized dealer. E—Engine Oil Pressure Indicator: NOTE: It is normal for light to come on at start-up and stay on for a few minutes. O—Transmission Oil Pressure Gauge: IMPORTANT: If needle remains in red zone after warm-up or moves to red zone while operating, power train damage may occur. See your authorized dealer to correct low pressure. Indicator will light and stay lit when engine coolant temperature is too high.

STOP indicator will light and stay lit and the audible alarm will sound. Immediately park the machine in a safe environment, stop engine and take corrective action. After the engine is started, the gauge needle must move above the point within a few seconds. If not, stop engine and see your authorized dealer. F—Transmission Oil Temperature Indicator: Indicator will light and stay lit when transmission oil temperature is too high. STOP indicator will light and the audible alarm will sound. Immediately park the machine in a safe environment, stop engine and take corrective action. P—Front and Rear Work Lights Switch: Push upper half of switch to turn front and rear work lights on.

Push lower half to turn lights off. Continued on next page HG31779,00000AB -19-11JUL02-1/2 2-1-2 070813 PN=28