John Deere 450H, 550H, 650H — Instrument Panel Functions (Later Machines)

Operation—Operator's Station Instrument Panel Functions (Later Machines) 1—Select Button: With key switch “On”, press and hold the select button to cycle between displays on the display window. until it drops below 110° C (230°F). Immediately park the machine in a safe environment, stop engine and investigate the problem. 2—Display Window: The display window has seven displays. Press and hold the select button to cycle between displays on the display window when the monitor panel is active:

Transmission Speed Setting Tachometer Hour Meter Voltmeter Temperature Light for Transmission Oil Temperature or Hydraulic Oil Temperature Hydraulic Oil Temperature Transmission Oil Temperature 11—Transmission Oil Filter Indicator: Indicator will light when transmission filter element is restricted. It is not necessary to stop operation, but the cause should be investigated as soon as possible. It is normal for this light to remain lit for several minutes after start-up in cold weather. In extremely cold weather, it is a good practice to operate at reduced engine speed so the light stays off. 12—Transmission Oil Temperature Indicator:

Indicator will light when transmission oil temperature reaches 93°C (200° F) and stay lit until temperature drops below 90° C (195° F). The display window will automatically default to current temperature. Reduce load and monitor temperature. 3—Engine Coolant Temperature Gauge: When engine coolant temperature is too high the gauge needle will move to the red zone. Immediately take load off the machine and run engine at fast idle. If gauge needle stays in red zone after several minutes of idling, stop engine. See your authorized dealer. The STOP indicator will light and audible alarm will sound when transmission oil temperature reaches 95° C (205° F).

Immediately take load off the machine and run engine at fast idle for several minutes. If indicator continues to stay on after several minutes of idling, stop engine and investigate the problem. 4—Engine Oil Pressure Gauge: After engine is started, gauge needle must point to green zone immediately and not drop into red zone after warm-up. If gauge needle drops into red zone, stop engine. See your authorized dealer. 13—Check Service Code Indicator: If service code indicator stays lit, there is an electrical problem in the transmission control system. It is not necessary to stop the machine. 5—Fuel Level Gauge: Gauge will reflect fuel level in tank.

Fuel level gauge needle will enter red zone when fuel level in tank is too low. The transmission controller will automatically put the machine in an operational mode that will not harm the machine. 6—Seat Belt/Park Brake Indicator: Indicator will light when key switch is and park lock lever is in up (locked) position. The service code that is present is displayed in the transmission controller display window. This service code number pinpoints the problem and is a very important aid for your authorized dealer to quickly diagnose the problem. Always relay this code number to your dealer when reporting your problem. 7—Engine Alternator Voltage Indicator:

Indicator will light when battery/alternator is below 12-volts. It is not necessary to stop operation, but the cause should be investigated as soon as possible. 8—Engine Air Filter Restriction Indicator: Indicator will light when engine air filter element is restricted. It is not necessary to stop operation, but the cause should be investigated as soon as possible. The service code indicator will go out when the machine is shut down. 14—Stop Indicator: 9—Hydraulic Oil Filter Indicator: Indicator will light when hydraulic filter element is restricted. It is not necessary to stop operation, but the cause should be investigated as soon as possible. IMPORTANT:

If STOP indicator flashes and alarm sounds, in most cases stop engine immediately and investigate cause of problem. Do not start engine until problem has been corrected. 10—Hydraulic Oil Temperature Indicator: Indicator will light when hydraulic oil temperature reaches 107° C (225° F) and stay lit until temperature drops below 104° C (220° F). The display window will automatically default to current temperature. It is not necessary to stop operation, but the temperature must be monitored. The STOP indicator flashes and alarm sounds when:

Engine oil pressure is too low Transmission oil temperature is excessively high Engine coolant temperature is excessively high Hydraulic temperature is excessively high The STOP indicator will light and audible alarm will sound when hydraulic oil temperature reaches 112° C (235° F) Continued on next page HG31779,00000AC -19-11JUL02-1/2 2-1-4 070813 PN=30