Maintenance—Machine Diesel Fuel Consult your local fuel distributor for properties of the diesel fuel available in your area. Sulfur Content for Tier 3 and Stage III A Engines Use of diesel fuel with sulfur content less than 1000 mg/kg (1000 ppm) is RECOMMENDED Use of diesel fuel with sulfur content 1000–5000 mg/kg (1000–5000 ppm) REDUCES oil and filter change intervals. BEFORE using diesel fuel with sulfur content greater than 5000 mg/kg (5000 ppm), contact your John Deere dealer In general, diesel fuels are blended to satisfy the low temperature requirements of the geographical area in which they are marketed. Diesel fuels specified to EN 590 or ASTM D975 are recommended.
Renewable diesel fuel produced by hydrotreating animal fats and vegetable oils is basically identical to petroleum diesel fuel. Renewable diesel that meets EN 590 or ASTM D975 is acceptable for use at all percentage mixture levels. Sulfur Content for Tier 2 and Stage II Engines Use of diesel fuel with sulfur content less than 500 mg/kg (500 ppm) is RECOMMENDED. Use of diesel fuel with sulfur content 500–5000 mg/kg (500–5000 ppm) REDUCES the oil and filter change interval BEFORE using diesel fuel with sulfur content greater than 5000 mg/kg (5000 ppm), contact your John Deere dealer Required Fuel Properties In all cases, the fuel shall meet the following properties:
Cetane number of 43 minimum. Cetane number greater than 47 is preferred, especially for temperatures below –20°C (–4°F) or elevations above 1500 m (5000 ft.). Cold Filter Plugging Point (CFPP) should be at least 5°C (9°F) below the expected lowest temperature or Cloud Point below the expected lowest ambient temperature. Fuel lubricity should pass a maximum scar diameter of 0.45 mm as measured by ASTM D6079 or ISO 12156-1. Sulfur Content for Other Engines Use of diesel fuel with sulfur content less than 5000 mg/kg (5000 ppm) is recommended. Use of diesel fuel with sulfur content greater than 5000 mg/kg (5000 ppm) REDUCES the oil and filter change intervals.
Diesel fuel quality and sulfur content must comply with all existing emissions regulations for the area in which the engine operates. DO NOT use diesel fuel with sulfur content greater than 10 000 mg/kg (10 000 ppm). IMPORTANT: Do not mix used diesel engine oil or any other type of lubricating oil with diesel fuel. Sulfur content for Interim Tier 4 and Stage III B engines Use ONLY ultra low sulfur diesel (ULSD) fuel with a maximum of 15 mg/kg (15 ppm) sulfur content. IMPORTANT: Improper fuel additive usage may cause damage on fuel injection equipment of diesel engines. DX,FUEL1 -19-11APR11-1/1 Low Sulfur Diesel Fuel Conditioner CONDITIONER.
It provides lubricating properties along with other useful benefits, such as cetane improver, anti-oxidant, fuel stabilizer, corrosion inhibitor and others. John Deere PREMIUM DIESEL FUEL CONDITIONER is specifically for use with low sulfur fuels. Nearly all other diesel fuel conditioners only improve cold weather flow and stabilize long-term fuel storage. They do not contain the lubrication additives needed by rotary fuel injection pumps. When possible, use existing fuel formulations for engines used off-highway. This fuel will not require any additives to provide good performance and engine reliability.
However, many local fuel distributors will not carry both low and regular sulfur diesel fuels. If the local fuel distributor will supply only low sulfur fuel, order and use John Deere PREMIUM DIESEL FUEL TX,45,JC2126 -19-15AUG97-1/1 Testing Diesel Fuel operations, bacteria, cloud point, acid number, particulate contamination, and whether the fuel meets specification. A fuel analysis program can help to monitor the quality of diesel fuel. The fuel analysis can provide critical data such as cetane number, fuel type, sulfur content, water content, appearance, suitability for cold weather Contact your John Deere dealer for more information on diesel fuel analysis.
DX,FUEL6 -19-14APR11-1/1 3-1-1 070813 PN=77