14. WHEN STARTING SWITCH IS TURNED ON, WIPER MOTOR DOES NOT OPERATE · Before disconnecting the connector, always turn the starting switch OFF. · Before carrying out below procedure, check all the related connectors are properly inserted and the fuse No. 9, 14 and 20 are not blown out. · After checking, insert the disconnected connectors again immediately unless otherwise specified. CN-21 CN-22 CN-5 WASHER PUMP 2 DO-5 CN-17 15 1 MOTOR DRIVE+ 4 2 1 16 FUSE GND VCC 5 6 3 4 17 NO.20 FUSE CONTINUE 24V 7 5 NO.9 18 WASHER P/P WASHER SIG. 8 9 6 7 19 20 INT.
SIG 10 11 8 21 WIPER CUT SW N.C 12 WIPER MOTOR CONTROLLER FEED BACK 13 CS-53 WIPER CUT SW FUSE No.14 CN-376 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 INT WIPER/OUT R LH WIPER/OUT R RH WORK LIGHT CABIN LIGHT OVERLOAD SW WASHER/OUT F LH HEAD LIGHT BEACON LAMP IG 24V CAN HI(2) CAN LO(2) GND NC NC NC NC NC NC NC NC NC NC NC NC NC NC GND NC NC NC NC NC NC NC RDU(RELAY DRIVE UNIT) 900L6ES16 6-37 3 5 4 6 M 2 1 2 3 4 5 6 NO NO Check operation wiper cut switch ont sliding door Check valtage en-close between CN-141 YES YES (11) and chassis Check voltage NO Front sliding door-close between CN-376 Voltage :
4~5V Check operation (1) and chassis of relay drive NO Starting switch : ON YES unit LED ON. Vottage : 20~30V Starting switch : ON ⓐ Push wiper switch button YES Check voltage between NO CN-376 (12) and chassis Intermittent NO Check voltage CN-376 ⓐ (11) and chassis Check operation Washing of wiper motor Check voltage CN-376 and controller (3) and chassis check voltage YES CN-141 (7) and Sarting switch : ON chassis, CN-21 Voltage : 0~1V (4) and chassis NO Starting switch : OFF Voltage : 20~30V Check voltage CN-141 (6) and YES chassis Starting switch : ON Check continuity YES Voltage :
20~30V NO between CN-141 (2)-CN-376 (3), CN-141 (9)-CN-376 (11), CN-141 (10)-CN-376 (12), ⓑ NO CN-141 (5)-Chassis , Check wiper CN-141 (1)-CN-21 (5), motor resistance CN-141 (3)-CN-21 (6), between CN-21 YES CN-141 (4)-CN-21 (2), (2)-CN-21 (6) CN-141 (13)-CN-21 (3) YES Resistance :
3~4Ω Cause Remedy Defective wiper cut switch Short circuit in wiring harness or poor contact between CN-141 (11)- CS-53 Defective relay drive unit 1) Recheck fuse No.14 2) Disconnection in wiring harness or poor contact between CN-376 (1)-Fuse No.14 Defective relay drive unit 1) R echeck fuse No.9 2) D isconnection in wiring harness or poor contact between CN-141 (7)-Fuse No.9, CN-21 (4)-Fuse No.9 1) R echeck fuse No.20 2) D isconnection CN-141 (6)-Fuse No.20 ⓑ Disconnection in wiring harness or poor contact Defective wiper motor Defective wiper motor controller Replace Repair or replace (after clean) Replace Replace Repair or replace (after clean) Replace Replace Repair or replace (after clean) Replace Repair or replace (after clean) Repair or replace (after clean) Replace Replace 2 1 M Check voltage between CN-376 (12) a Intermittent Check voltag CN-376 (12) a nd chassis Check voltag e CN-376 (11) and cha Washing Check voltag (11) and cha ssis Check voltag e CN-376 (3) and chas sis