Freightliner — Freightliner Business Class M2 Workshop Manual

Chassis Electrical Control Systems 54.40 General Information grounded feedback circuit from the closed pressure switch indicates that the interaxle lock is activated and pressure is being supplied to the interaxle lock. An open feedback circuit indicates that the interaxle lock is not activated, or there is a malfunction; the interlock switch is turned on but the pressure switch is still open. mission. With the engine running, the two-speed axle is shifted between high and low ranges by a momen- tary, two-position smart switch. Press the upper half of the axle shift switch to change the axle speed. See Fig. 2 .

If the engine is turned off, then restarted, the two-speed axle will default to low range. On a vehicle with a two-speed tandem axle, the elec- tronic controls of the interaxle lock need to take into account the range position of the axles. Both axles must be in the same state (either high or low range) for the interaxle lock to be turned on or remain activated. The electronic controls of the interaxle lock incorpo- rate axle range position input as well as a second pressure-switch feedback to the CHM. Utilizing the feedback from the axle and pressure switches, the control logic provides a time delay to ensure proper function and to prevent damage.

Once the interaxle lock is activated, any axle-range change may cause the interaxle lock to deactivate. A shift made from one range to another while the interaxle lock is acti- vated requires that both axles reach the change state quickly before feedback indicates that the axles are not in the same drive range. For a description of the axle shift feature, see the information under the "Axle Shift" heading in this subject. 10/26/2001 f610594 Fig. 2, Axle Shift Switch When the axle shift switch is activated, the CHM transmits a low-current output to a normally closed air management unit (AMU) solenoid. On AAVA ve- hicles, the solenoid current is about 1.5 amps.

The 2010 CHM does not have the current sourcing ability to drive these solenoids, so a relay in the chassis PDM is added to the circuit. The energized solenoid opens and supplies compressed air to the gear hous- ing. The air sent to the housing shifts the axle into high gear. Pressing the axle shift switch again directs the CHM to remove the current supply to the AMU/ AAVA solenoid, which stops the air supply to the gear housing. With a no-air condition at the housing, the axle shifts into low gear. Axle Shift Two-speed axle shift is an option available on a ve- hicle with a single or tandem axle.

This option is available on a vehicle with a manual or automatic transmission; however, nonmultiplexed controls are only available on a vehicle with a manual transmis- sion. A vehicle with a two-speed axle allows the op- erator to shift the drive axle between high and low gear ranges. At any time, the operator may change axle speeds to take mechanical advantage of differ- ent driving conditions. Feedback to the CHM is provided by switches lo- cated on each drive axle. When an axle shifts into the low-speed range, the axle switch closes and completes a ground signal to the CHM.

The CHM uses the feedback signal(s) to determine if the sys- tem is functioning properly (axle shift switch confirms axle shift switch selection), or if there is a malfunc- tion (axle shift switch does not confirm axle shift switch selection). Each rear axle of a tandem-axle vehicle has its own AMU/AAVA solenoid and axle switch. The CHM also monitors the feedback of both axle shift switches to make sure that the rear axles are in the same speed range. NOTE: Since axle speed can be changed at any time, it is the driver’s responsibility to ensure that axle speed selection is not done under harmful con- ditions, such as selecting low gear when the engine is at high rpm.

Multiplexed Controls Two-speed axle feedback is also provided to the En- gine Control Module (ECM). For the MBE900 engine, the system provides axle position input via the J1939 data line messages between the CHM, BHM, and Multiplexed controls for the two-speed axle are avail- able on a vehicle with a manual or automatic trans- Business Class M2 Workshop Manual, Supplement 22, September 2012 050/2