Cab Heater and Air Conditioner, Valeo 83.00 General Information Effect of Pressure on Boiling or Condensation air in the cab and prevent fresh outside air from en- tering the system. Recirculation mode helps to warm or cool the cab more quickly, but the cab tends to build more humid- ity and fog the windows in recirculation mode. Allow- ing fresh air to enter the system and circulate helps defog the cab. Refrigerant circulates through part of the air condi- tioning system under high pressure. It expands to a lower pressure vapor in the evaporator, then flows to the refrigerant return port in the compressor.
As pres- sures in the closed refrigerant circuit vary, the tem- perature of the refrigerant also varies: as pressure increases, temperatures increase; as the pressure decreases, temperatures decrease. In its low pres- sure gaseous state in the evaporator, a good refriger- ant such as R–134a absorbs a large amount of heat from the cab, and carry the heat to the condenser where it transfers into the outside air. On vehicles built prior to May 2, 2003, the system automatically returns to the fresh air mode and the recirculation light turns off, after being in the recircu- lation mode for 20 minutes.
Pushing the recirculation button again returns the system to recirculation mode for another 20 minutes. If the recirculation button is pressed in recirculation mode before 20 minutes have passed, the system will switch to the fresh air mode. Heating, Ventilation and Air Conditioning (HVAC) System General Description On vehicles built from May 2, 2003, the system auto- matically enters partial recirculation mode for five minutes, to bring some fresh air into the cab. After five minutes in partial recirculation mode, the system will automatically resume full recirculation for another 20 minutes.
The full and partial recirculation cycle will repeat as long as the system remains in recirculation mode. If the recirculation button is pressed when the system is in either recirculation mode, recirculation mode will be canceled. There may be a slight change in the sound within the cab as the system goes into, and out of, partial recirculation mode. Stated simply, the air conditioning system operates by circulating refrigerant between two heat transfer units. The unit in the cab absorbs heat from the air in the cab, and the one in front of the radiator gets rid of the heat from the cab, into the outside air.
Both units consist of coiled tubing, covered with fins so they transfer heat most efficiently. The heat transfer unit in the cab is called the evapo- rator. It is mounted in the dashboard, next to the blower fan. It absorbs heat out of the air in the cab and transfers it to the refrigerant, which carries the heat away. The other heat transfer unit, called the condenser, is usually mounted low in the front end of the vehicle. Hot refrigerant from the evaporator circu- lates to it, and gives off the stored heat to the air being pulled in by the engine cooling fan and the ve- hicle’s forward movement.
Description of Components Actuator The actuator is a combined motor and gearbox which drives the levers and doors within the HVAC assem- bly. Movement of the levers and doors is controlled by the settings on the climate control panel. A propor- tional feedback signal is returned from each actuator to the control panel to provide current position infor- mation. There are three actuators on the HVAC as- sembly: a temperature blend actuator, a recirculation actuator, and an air distribution actuator. Binary Switch Inside the cab, the blend air heating, ventilating, and air conditioning (HVAC) system uses a brushless blower motor to circulate temperature-controlled air through the cab.
The rate of airflow is controlled by a multi-speed fan switch. The temperature control switch on the climate control panel sets the desired temperature in the cab. A binary switch disengages the refrigerant compres- sor clutch, to protect the compressor from harmful operating conditions. It performs two functions. The air selection switch on the control panel controls ducting air from the blower through the cab. On ve- hicles with air conditioning, a recirculation button on the control panel allows the driver to recirculate the If refrigerant system pressure falls too low, the binary switch disengages the compressor Business Class M2 Workshop Manual, Supplement 18, September 2010 050/2