Hood 88.00 Hood Repair Hood Reinforcement Rebonding NOTE: When using Ashland Pliogrip 7773 or 7779, insert the two tubes of adhesive into the applicator and dispense a 3/8-inch (10-mm) di- ameter bead of uniform green-colored adhesive at the bonding surface. Discard any adhesive that does not show this uniform green color. 1. If rebonding a joint that has partially separated, completely separate the reinforcement from the hood using a heat gun and putty knife. Remove as much of the old adhesive as possible. The heat gun will soften the adhesive and allow it to be peeled off the FRP. 6.
Within 3-1/2 minutes (7773) or within 10 minutes (7779) of applying the bead, align the part on the hood and clamp it firmly in place. If it is a large part, install the clamping bolts. Tighten the clamps or clamping bolts just enough to ensure that a uniform amount of pressure is applied along the seam. Ideally, the adhesive should be compressed to form a bondline 1-inch (25-mm) wide and 0.030-inch (0.76-mm) thick. This thick- ness can be ensured by sprinkling 0.030-inch (0.76-mm) glass beads into the adhesive before mating the parts.
If the parts cannot be separated, work folded medium-grit sandpaper or a section of a steel hacksaw blade between the two surfaces to re- move the old adhesive. 2. Scuff the surfaces with 80- to 220-grit sandpaper. 3. Clean the surfaces to be bonded with Ashland 6036 solvent or methylene chloride. Inspect the area closely to be sure all of the old adhesive, dirt, water, grease, and oils are removed. 4. If replacing a large part, align the part on the hood and clamp it in place. Drill holes through the bonding surfaces and install clamping bolts in the holes. Use two washers, one on each side of the joint. See Fig. 2 .
There should be enough clamping bolts to hold the hood in place and keep the bonding surfaces together, or at least one bolt every 12 to 18 inches (30 to 45 cm). Remove the part for application of adhesive. 7. Before it cures, remove any excess adhesive that squeezes out the edges of the bond. 8. Remove the clamps after the adhesive has cured for 30 minutes (7773) or for 60 minutes (7779). 9. If holes were drilled for clamping bolts, repair them using the instructions under "Crack or Small Hole Repair." 10.
If necessary, prime and paint the repair area us- ing the instructions under "Surface Damage Re- pair." Crack or Small Hole Repair 1 3 A crack (fracture) or small hole through the laminate requires repair with a fiberglass-reinforced patch. 1. Examine the damage to the hood or apply hand pressure all around the damaged area to check for any concealed damage. 4 02/10/94 f880125a 2. If a sound-absorbent liner is present on the un- derside of the damaged area, peel away the liner to provide an adequate working area. 1. Nut 2. Washers 3. Bolt 4. Bond Joint 3. Clean the damaged area on both sides of the hood or with xylene, acetone, or equivalent grease- and wax-removing solvent.
Inspect the area closely. All dirt, water, grease, and oils must be removed. 5. Following the manufacturer’s instructions, use enough adhesive to bond the parts together. Use Ashland Pliogrip urethane cartridge materials 7773 or 7779. Fig. 2, Clamping Bolt at Bond Joint 4. If repairing a crack, use a 1/8-inch (3-mm) diam- eter bit to drill a hole completely through the un- cracked laminate 1/8 inch (3 mm) from each end Business Class M2 Workshop Manual, Supplement 0, September 200 2 140/2 2 2