John Deere OMAL171363 (7430 and 7530) — Additional Information About Diesel Engine Coolants and John Dee

Fuel, Lubricants, Hydraulic Oil and Coolant John Deere COOL-GARD™II Coolant Extender Some coolant additives will gradually deplete during engine operation. For John Deere COOL-GARD™II Premix, COOL-GARD II PG Premix, and COOL-GARD II Concentrate, replenish coolant additives between drain intervals by adding John Deere COOL-GARD II Coolant Extender. IMPORTANT: Do not add a supplemental coolant additive when the cooling system is drained and refilled with any of the following: John Deere COOL-GARD II John Deere COOL-GARD II PG John Deere COOL-GARD II Coolant Extender should not be added unless indicated by coolant testing.

The use of non-recommended supplemental coolant additives may result in additive drop-out, gelation of the coolant, or corrosion of cooling system components. John Deere COOL-GARD II Coolant Extender is a chemically matched additive system for use with all John Deere COOL-GARD II coolants. John Deere COOL-GARD II Coolant Extender is not intended for use with nitrite-containing coolants. Add the recommended concentration of John Deere COOL-GARD II Coolant Extender. DO NOT add more than the recommended amount. COOL-GARD is a trademark of Deere & Company DX,COOL16 -19-20APR11-1/1 Operating in Warm Temperature Climates John Deere engines are designed to operate using glycol base engine coolants.

the same level of corrosion inhibitor as John Deere COOL-GARD II Premix (50/50). Always use a recommended glycol base engine coolant, even when operating in geographical areas where freeze protection is not required. IMPORTANT: Water may be used as coolant in emergency situations only. Foaming, hot surface aluminum and iron corrosion, scaling, and cavitation will occur when water is used as the coolant, even when coolant conditioners are added. John Deere COOL-GARD™II Premix is available in a concentration of 50% ethylene glycol. However, there are situations in warm temperature climates where a coolant with lower glycol concentration (approximately 20% ethylene glycol) has been approved.

In these cases, the low glycol formulation has been modified to provide Drain cooling system and refill with recommended glycol base engine coolant as soon as possible. COOL-GARD is a trademark of Deere & Company DX,COOL6 -19-03NOV08-1/1 Drain Intervals for Diesel Engine Coolant Drain and flush the cooling system and refill with fresh coolant at the indicated interval, which varies with the coolant used. If John Deere COOL-GARD™II Premix, COOL-GARD II PG Premix, or COOL-GARD II Concentrate is used, but the coolant is not tested OR additives are not replenished by adding John Deere COOL-GARD II Coolant Extender, the drain interval is four years or 4000 hours of operation.

This drain interval only applies to COOL-GARD II coolants that have been maintained within a 40—60% mixture of concentrate with quality water. John Deere COOL-GARD™II Premix, COOL-GARD II PG Premix and COOL-GARD II Concentrate are maintenance free coolants for up to six years or 6000 hours of operation, provided that the cooling system is topped off using only John Deere COOL-GARD II Premix or COOL-GARD II PG Premix. If a coolant other than COOL-GARD II, or COOL-GARD II PG is used, reduce the drain interval to two years or 2000 hours of operation. Test the coolant condition annually with Coolant Test Strips designed for use with John Deere COOL-GARD II coolants.

If the test strip chart indicates that additive is required, add John Deere COOL-GARD II Coolant Extender as directed. COOL-GARD is a trademark of Deere & Company DX,COOL11 -19-14APR11-1/1 80-9 030612 PN=206