PIPER COMANCHE SERVICE MANUAL s-ao. Flap Coaaou. (PA·l~.) 5-11. Remcml Of Plap CoDtrola. (PA·Z4-400.) (Refer to Filuft 5'5.) . a.. Accesl (or removal of the flap aauatiDI mcdwIism and flap comrol cables within the fusdqe may be reached by mnovinJ reu seat and .. companmCftt floor p .... Acc. to co.nrols iD the wiftI may be reached by remOYinJ wheel well spluh pill aod &Cecil piau to the flap bellcnnk. b. Remove the flap tnnIftl_on IIIaIlbly by dixonnectiDI the motor elet:!rica1lelds. emetine pin (16) &t the aansmiIIion hou'" and remorial bolt (23) at the forward section of the &ctlI&tinr screw. c.
The amaatinl arm, (IS) 1ft mnoml by dilc0nnectiDI the flap push-puU concrol cables clevis, the step lock maR cable on tbe n,ht ann. and the flap position sender rod. Remove the pivot bolt at the tOP spar support Nbe and the flap pide bracket. d. To remove the flap puah-pu11 conuol cable (5) remove the devil end and 10cIcnut from actuator end of the cable. Disconnect the support clamps and draw the cable from its support tube. WithiD the win,. disconnect and remove the devis end at the flap bdlcrank. Enta' throUJb the wbee1 well and remove the support tube locknut. Oraw the cable from the wiaI iDto the fuIeIap. e. Oilconnect the flap control rod and remove the bolt ICCUrinI the bdlcranJc. f.
Removal of the step lock mechanism(.... )ud support cable (27 dilconDect the mum spring (43) at the inboard side of the _heel well. Remove the aft W'iJlllairina. tbe accell plate located at the inboard, under side o( the flap and back the adjusriDI nut (45) off the csble end. Unbolt the mechanism from the inboard and aft sides of the winJ and remove with step loclc and support cable. 5-22. lnsalIaaon Of Flap Concrola. (PA-Z-4-400.) (Refer to Finft 5·5.) a. To iDsa.ll the flap acmaUq meclwUsm .-embly. connect the cODtrol arms (14 and 15) to the upper spar support tube aDd iDIcn: the pivot bolt. TilhtcJI the bolt to a IIIUI fit with no biDdint of the b.
The aetUaan, motor and tranSmission may be insralled at a unit. Place the transmission end between the two brackcu leadinJ from the spar mpport. Wen lockiDI pin ;lila safety. Connect the aetuatinl SCttW (Z2) to the lower portion of the &CtUacinl arms. iIIICrt bolt (23) lAd seeure. Connect the electricallcads to the motor. trierri,. to the dcctrical cliqnm in Section L"{. Operue the motor to usure proper eleetric:aJhookup. c. The nap bellcrank (6) may be iIlstalled by placinJ intO posicion. iftltl11iftl the pivot bolnecuring the bellc:rank and a,uten to a sllUI fit. Install the flap conttOl rod (33). d.
The flap push1'ull concrol cable may be iasuUed by drawm, the cable from the fuse1aJe intO the win,. Place the cable end thro. the support tube. locknut and to the flap bcUcrank. Install the able end and eenneet to the beUcnnk. Secure and safety the locknut at the support Nbe. Within the fusclqe. insert the cable throUlh the suPPOrt tube and locknut. secure and safety. ann~ IftSUlI the flap pide bracket aDd conacet me flap pOlition sader rod (12) to the contrOl arms. e. To insull the Step loclt mechanilm(44)and mum cable (21) in the rilbt wiftt. enter throUSb the wheel well and iqsull the lock mechanism with the rcmm cable wtapped uound the pulley and secured.
Insert the cable end to the f1&p, throUlh the trailin& qe of the wine and iDto the flap. Start the adjustirl! nut (45) a few threads onto the cable end. Draw the tension SPrint in place at the inboard side of the wheel well. Attach the step lock tdeuc cable to the lock release and to the control arms within the fuselage. Install cable pulley and secure. f. Rig and adjust per Puqraph '·23 and rciDstal1 a.ccess panels, wheel well splash pan. rear sat. etc. SURFACE CONTROLS ISSUED: 8118n2 IG12