BAIC — BAIC Comanche Service Manual: Comprehensive Guide for PA-24 Series Aircraft

PIPeR COMANCHE SERVICE MANUAL 7C-51. R.mOҐll1 Of Mapero. Before rernoviq the mqnftO. make sure mapcto switches a.re off. &. Remove the harness assembly tmniDal plate from the mqncto. WARNING The mapctO is not iDccma1ly JI01IDtied; wheD the pound lead is discouectat. the mapeto is hot. RcmOYinl me hamal wembly termiD&l plat. tim and jnn,m,. it I.aa millimiza the dafta'er of startiDI the enpne accidcDtally when the pound lad is ranowd from the mapcto. b. Disconnect the poud 1ead IIld the retard spark lead on the left mqncto. at the rn.qncto. c. Remove the nuts andwubcrs &Dd draw the mqactO from the entine. a. Remove the cover to the c:oncaa(s). clistributor block. etc. b.

To internally time the main CODtact assembly of either the dual-breaker rnqnetos or the si,.le-brc&ker mapctot. proceed u follows: 1. LoOllD the nut scc:uriq the drive place to the mapeto shah sufficieDuy in order to install the Sc:iDtilla 11-3465 Rotor Holdiq Tool uDder the DUt and fiat washer u shown in Fipre 7C-IO. Tighten the nut securely. 7C·52. TimiD, Procedure. (Intemal TimiD,.) 2. Remove the timiDI inspectiOD plul from the top of the mqDctO. Tum rotating mqnet to proper neutral position. This pOsitiOD is determined by locatitll keyways on drive end of magnet shaft at 12 o'clock with respect to name plate on bousq. Tichtcn &djustint knob of 11-3465 Rotor Holdi,.

Tool until pressure is applied OD bousiD. flaqe preventiq mapct from tumin,. 3. Looscn aDd rotate cam. until cam follower of main contact uscmbly rests on lliJhcst point of cam lobe. Adjust main contact uaembly to obtain the c:laraDce of 0.016 inch. Ti,hten m&Ul contact assembly securin. saews to 20-25 i.nc:.b pounds. 4. Install the 11-3693 Timiq Plate A_mbly and the 11-3149 POUlter Assembly of the 11-3150 Sc:intilla Timq Kie to breaker compartment of mapeto. (Refer to Figure 7C·1l.) Align pointer assembly With the 0 marlc on timiq plate.

LoolCll adjusting knob of 11-8465 Roeor Holdq Tool sad tum routing mqnet in normal 4irection of rotation until pointer indexes with the respective E lap mark (1 S~ ~ t' ). Tighten adjustialltnob of 11-3465 Tool and remove the 11-8149 Pointer Assembly from tnalfteto. t.:sing a timing licht. adjust main contact points to just open. This adjusanent shall be made by rotating C111\. in opposite direction of rotation. a few dqrees beyond poine where contactS close. Then rotate cam in normal direction of roution until CODUetS just open. While holdin. cam in this exact position. push cam on rDafllct shaft II far as pomble with the fmlftS. Extreme care must be exercised in this operation.

If earn adjustment is chanp in the slilhtest dqree. the timinl of the mapeto will be thrown off. Do not drive cam on shaft W1th a mallet or other in'tr\lmcnt. TiJbtcn the securiDi screw thereby dnwing the cam down. evenly and tlght.ly. Torque screw to 16·20 inch pounds. Loosen the 11-346S Rotor Holdinl Tool adjusting knob and return rotatin. mqnet to neutral position. Reinstall the 11-8149 Pointer Assembly over 0 0 mark on timing plate. Rotate mTet shaft in normal direction of rOtanOD and check for openinf of main o:ontact points at E gap setting (1 S = ~ ). . POWER PLANT ISSUED: 8/18/72 2 H13