DISASSEMBLY AND ASSEMBLY FINAL DRIVE 2) Using tool J5 , press fit bearing outer race (41) to cage (40). Press fitting force for bearing: 1 – 14 kN {0.1 – 1.4 tons} Table 1 3) Install the O-ring to cage assembly (37) and adjust shim (39). 4) Adjustment of shim Adjust the clearance of the pinion bear- ing according to the following procedure. i) Tighten mounting bolts B , C , E , and F of cage (40) evenly. 3 Mounting bolt: 20 Nm {58 kgm} ii) Under this condition, measure clear- ances a and b between cage (40) and case (34) with feeler gauges. iii) Set shim thickness c from the total of clearances a and b , referring to Table 1.
iv) Install selected shim (39) to cage (40) and tighten the 6 mounting bolts of cage (40) evenly. 3 Mounting bolt:
98 – 123 Nm {10 – 12.5 kgm} 30-118 D85EX-15 (2) a + b (mm) Number of shims to be used t = 0.15 t = 0.5 t = 1.0 Total thickness of shims (mm) Larger than Below t = 0.15 t = 0.5 2.95 3.05 5 1 1.75 3.05 3.15 2 1 1 1.80 3.15 3.25 9 1 1.85 3.25 3.35 6 1 1.90 3.35 3.45 3 1 1 1.95 3.45 3.55 2 2.00 3.55 3.65 7 1 2.05 3.65 3.75 4 1 1 2.10 3.75 3.85 1 2 2.15 3.85 3.95 8 1 2.20 3.95 4.05 5 1 1 2.25 4.05 4.15 2 2 2.30 4.15 4.25 9 1 2.35 4.25 4.35 6 1 1 2.40 4.35 4.45 3 2 2.45 4.45 4.55 1 2 2.50 4.55 4.65 7 1 1 2.55 4.65 4.75 4 2 2.60 4.75 4.85 1 1 2 2.65 4.85 4.95 8 1 1 2.70 4.95 5.05 5 2 2.75 5.05 5.15 2 1 2 2.80 5.15 5.25 9 1 1 2.85 5.25 5.35 6 2 2.90 5.35 5.45 3 1 2 2.95 5.45 5.55 3 3.00 5.55 5.65 7 2 3.05 5.65 5.75 4 1 2 3.10 5.75 5.85 3 3 3.15 5.85 5.95 8 2 3.20 5.95 6.05 5 1 2 3.25 6.05 6.15 2 3 3.30 6.15 6.25 9 3 3.35 6.25 6.35 6 1 2 3.40 6.35 6.45 3 3 3.45 6.45 6.55 1 3 3.50 6.55 6.65 7 1 2 3.55 6.65 6.75 4 3 3.60 6.75 6.85 1 1 3 3.65 6.85 6.95 8 1 2 3.70 6.95 7.05 5 3 3.75 7.05 7.15 2 1 3 3.80 7.15 7.25 9 1 2 3.85