Cummins — 3666003

C Series Propeller Shaft Section 16 - Mounting Adaptations - Group 16 Page 16-41 The couplings must be aligned. A straight edge can be used to help align the couplings Use a feeler gauge (3) to check the alignment of the coupling in four different places, 90 degrees apart. The variation is to be within 0.051 to 0.102 mm [0.002 to 0.004 in]. If the flange is out of alignment the engine mounting will need to be adjusted until the alignment is correct. Refer to Engine Mounting/Drive Systems section in the Marine Recreational Installation Directions, Bulletin 3884649. Make sure all mounting bolts and nuts are torqued to the proper specifications.

Refer to Procedure 016-026, or the OEM literature. Bolt the coupling in place and torque to the specifications for the capscrew and bolt size. Specifications parts wiped or washed nearly free of oil. Do not use for plated parts. 2. Use for all capscrews and nuts whose threads and washer faces are lubricated. 1.

Use for all capscrews, bolts, and nuts coated only with the fastener manufacturer's rust preventive oil and use for Capscrews, Bolts and Nuts Torque for Fine and Coarse Threads SAE Grade 5 SAE Grade 8 (1) As Received (2) Lubricated (1) As Received (2) Lubricated N•m [ft-lb] N•m [ft-lb] N•m [ft-lb] N•m [ft-lb] 1/4 12 ± 1 [9 ± 1] 9 ± 1 [7 ± 1] 19 ± 1 [14 ± 1] 15 ± 1 [11 ± 1] 5/16 26 ± 3 [19 ± 2] 20 ± 3 [15 ± 2] 37 ± 3 [27 ± 2] 30 ± 3 [22 ± 2] 3/8 45 ± 4 [33 ± 3] 37 ± 3 [27 ± 2] 62 ± 5 [46 ± 4] 52 ± 4 [38 ± 3] 7/16 71 ± 5 [52 ± 4] 54 ± 4 [40 ± 3] 99 ± 8 [73 ± 6] 81 ± 7 [60 ± 5] 1/2 108 ± 8 [80 ± 6] 88 ± 7 [65 ± 5] 152 ± 11 [112 ± 8] 122 ± 9 [90 ± 7] 9/16 152 ± 11 [112 ± 8] 112 ± 11 [90 ± 8] 214 ± 16 [158 ± 12] 176 ± 14 [130 ± 10] 5/8 214 ± 16 [158 ± 12] 176 ± 14 [130 ± 10] 304 ± 22 [224 ± 16] 244 ± 20 [180 ± 15] 3/4 380 ± 27 [280 ± 20] 305 ± 27 [225 ± 20] 529 ± 41 [390 ± 30] 434 ± 34 [320 ± 25] 7/8 607 ± 43 [448 ± 32] 488 ± 41 [360 ± 30] 854 ± 68 [630 ± 50] 691 ± 54 [510 ± 40] 1 922 ± 68 [680 ± 50] 732 ± 61 [540 ± 45] 1302 ± 95 [960 ± 70] 1051 ± 81 [775 ± 60] 1 1/8 1152 ± 81 [850 ± 60] 915 ± 81 [675 ± 60] 1844 ± 136 [1360 ± 100] 1491 ± 115 [1100 ± 85] 1 1/4 1593 ± 115 [1175 ± 85] 1254 ± 102 [925 ± 75] 2508 ± 203 [1850 ± 150] 2034 ± 169 [1500 ± 125]