Fendt 900 Vario COM III — 1 General description of the common rail system

2000 - Overall system/engine A - General 9 T002534 Version 1 04-09-2009 tion" B091 - Sensor, water in fuel The signal is reported to the engine control unit and from there forwarded via the CAN bus system to the instrument panel (warning message) B092 - Sensor, charge air pres- sure/temperature Reports the "LDA function" charge air pressure and the charge-air temperature (NTC) Note: Two rotational speed sensors are fitted. These synchronise the injection, are used for diagnostics capabilities and to determine emergency running characteristics K034 relay (for R002 heater flange) The relay is energised at temperatures of 5°C and below.

In addition the indicator lamp on the instrument panel is energised Y035 EMR actuator The actuator is energised (PWM) by a certain control linkage movement (load demand) Comparison between EMR 2 (COM II) and EMR 3 (COM III). B090 - Sensor, oil pressure Reports the oil pressure 919 .. 0101-1000 925 .. 1001- 934 .. 0101-1000 919 .. 1001- 928 .. 0101-1000 934 .. 1001- 922 .. 0101-1000 928 .. 1001- 922 .. 1001- 931 .. 0101-1000 925 .. 0101-1000 931 ..

1001- Duty Duty Component Duty Actuators of the EMR 2 (COM II) programming A - General Component Duty B041 EMR (camshaft) sensor Reports the engine speed (actual value) B042 EMR (crankshaft) sensor Reports the engine speed (actual value); B048 sensor, water temperature Reports the engine temperature. This signal value is used for:

Engine manage- ment, temperature display and for activating the heater flange B053 charge-air tempera- ture/charge-air pressure sensor Reports the charge-air temperature (NTC) and the charge air pressure "LDA func- tion" B055 combination sensor, foot throttle sensor One signal value is reported to the A002 ECU, enhanced control (normal mode) The second signal value is processed in the A051 ECU, engine control unit (emer- gency mode, with loss of enhanced control functions) Position sensor in the Y035 EMR actuator Reports the position of the control linkage Note:

The two speed sensors B041 and B042 are fitted in order to provide diagnostics capability and emergency running characteristics Component Duty B004 - Vacuum switch (air filter) The signal is reported to the engine control unit and from there forwarded via the CAN bus system to the instrument panel (warning message) B055 - Sensor, foot throttle One signal value is reported to A002 ECU, enhanced control (normal operation) the second signal value is processed in the A051 ECU engine control unit (emer- gency mode, with loss of enhanced control functions) B085 - Camshaft speed sensor Reports the camshaft speed (actual value) and the position of the camshaft at cyl- inder 1 ignition B086 - Rail pressure sensor Reports the current pressure in the rail B087 - Fuel low pressure sensor Reports the fuel primary pressure B088 - Crankshaft speed sensor Reports the engine speed (actual value) and the position of the crankshaft TDC cylinders 1 and 4, or TDC cylinders 1 and 6.

B089 - Engine temperature sen- sor (Deutz) Reports the engine temperature. This signal value is used for: Engine manage- ment, temperature display and for activating the heater flange B090 - Sensor, oil pressure Reports the oil pressure B091 - Sensor, water in fuel The signal is reported to the engine control unit and from there forwarded via the CAN bus system to the instrument panel (warning message) B092 - Sensor, charge air pres- sure/temperature Reports the "LDA function" charge air pressure and the charge-air temperature (NTC) Note: Two rotational speed sensors are fitted.

These synchronise the injection, are used for diagnostics capabilities and to determine emergency running characteristics Component Duty K034 relay (for R002 heater flange) The relay is energised at temperatures of 5°C and below. In addition the indicator lamp on the instrument panel is energised Y035 EMR actuator The actuator is energised (PWM) by a certain control linkage movement (load demand)