John Deere 326D, 328D, 332D — Anti-Theft Security System Operation—If Equipped

Operation—Operator’s Station Selecting the Locking Method The Owner security code can be used to reset all codes back to their defaults by accessing the RESET ALL CODES menu option. The anti-theft security system resets all Operator security codes and the Owner security code to the default values when the Master security code is used to enable the system. The Owner security code can only be changed by someone using the Owner security code. The Owner security code must be entered before changing that code. Complete the following procedure to select the locking method for the anti-theft security system. Only someone with the Owner security code can configure the locking method.

There are four locking options available within the anti-theft security system: Prompt for Lock—Machine will only be locked if selected during EMU shutdown. Auto Lock, 5 Minutes—Machine is locked automatically 5 minutes after operator turns key switch to OFF position. Auto Lock, 60 Minutes—Machine is locked automatically 60 minutes after operator turns key switch to OFF position. Anti-Theft Off—Machine is not locked. 1. Press the MENU button on the EMU to access the Main Menu. 2. Press the NEXT button until “Main Menu AntiTheft” displays. 1. Press the MENU button on the EMU to access the Main Menu. 3. Press the SELECT button to display “AntiTheft Change Codes”. 2.

Press the NEXT button until “Main Menu AntiTheft” displays. 4. Press the SELECT button. Display shows: “Change Codes Operator 1 Code”. 5. If changing a different Operator security code or the Owner security code, press the NEXT button to display the appropriate security code to change. Proceed to next step. 3. Press the SELECT button to display “AntiTheft Change Codes”. 4. Press the NEXT button to display “AntiTheft Lock Mode”. 6. Press the SELECT button. Display shows “Enter Current Code 0 _ _ ” (3-digit system) or “Enter Current Code 0 _ _ _ _ (5-digit system). 5. Press the SELECT button to display “Enter Owner Code 0 _ _ ” (3-digit system) or “Owner Code 0 _ _ _ _ (5-digit system). 6.

Enter the current Owner security code. 7. Enter the current Operator security code or Owner security code for the code to be changed. The current locking method displays. a. Press the NEXT button or the BACK button to change the number displayed in the active (flashing) field. The NEXT button increments the current digit; the BACK button decrements the current digit. 7. Press the NEXT button to display the appropriate locking method: Turn ATS Off Prompt to Lock Auto Lock in 5 Min Auto Lock in 60 Min b. Press the SELECT button to accept the number displayed (flashing) in the active field and shift the active field to the next digit to the right. NOTE:

Pressing the SELECT button to accept the last digit (third digit or fifth digit depending on system configuration) processes the entered security code. If the code is incorrect, an error message appears on the monitor display. 8. Press the SELECT button to select the displayed locking method. 9. The selected locking method displays for 2 seconds before the EMU returns to the normal run-time display. The anti-theft security system allows three attempts to enter a valid security code before requiring the key switch to be turned OFF and ON to restart the process. Changing an Operator or Owner Security Code IMPORTANT:

If you do not intend to use all three available Operator security codes, make sure you change the codes you will not be using to something other then their default values. Leaving access to the machine by means of default codes is not recommended. 8. Enter the new security code. 9. The new security code displays for 3 seconds before the EMU returns to the normal run-time display. The following rules apply when changing security codes: An Operator security code can only be changed if that security code or the Owner security code is used during the change procedure. Resetting Operator and Owner Security Codes 1. Press the MENU button on the EMU to access the Main Menu.

Continued on next page OUT4001,0000504 -19-25MAR10-2/3 2-1-9 071713 PN=40