Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika micrometer. Taking the dummy shaft out. 5) Assembly of the bottom part of LP outer mikrometrickэm odpichem. Vyjmutн kontrolnн hřнdele. 5) Montбž spodku NT vnějšнho tělesa a VT , casing and HP, IP casing ST tělesa § Montбž pochozн podlahy do nбstavby kondenzбtoru – nenн - li již nainstalovanб § Pospupnй přemнstěnн spodků NT vnějšнho tělesa (ne jprve přednн čбst NT spo dku tělesa - blнže k ST turbнně, potй zadnн čбst NT spodku tělesa a nakonec střednн čбst NT spodku tělesa. § Uzemněnн dнlů spodku NT tělesa § Postupnй smontovбnн spodků NT vnějšнho tělesa na pozici.
§ Vyrovnбnн spodku NT vnějšнho tělesa . Měřenн hadicovou vodovбhou, měřenн polohy vэvrtu tělesa na kontrolnн hřнdel . Změna vэšky se provede podklбdбnнm kozlнků nebo zasouvбnнm zбkladovэch klнnů ve dvojici. Změna stranovй polohy posouvбnнm pomocн hydraulickэch zvedбků. § S tavba lešenн v potřebnйm rozsahu. Provedenн těstnostnнch svarů a dotaženн šroubů na předepsanэ moment. § Demontбž lešenн . Kontrola vyrovnбnн tělesa a sprбvnйho styku kozlнků s tělesem . § Montбž šroubů do dělнсн roviny, přнprava na vloženн vnitřnнch dнlů (mytн konzervace a promazбnн drбžek pro tělesa ucpбvek, pera ).
§ Assembly of walk-able platform into condenser neck if it is not already installed (first of all moving of bottom LP outer casing - closer to IP part of turbine, after that moving of rear bottom LP outer casing and finally middle LP outer casing. § Earthing of components of LP bottom casing § Gradually assembly of bottom parts of LP outer casing together on the position. § Levelling of bottom part of LP outer casing. Measuring with the hose water-level, measuring of position of circullar recess of casing against the dummy shaft.
Change of altitude is done by shimsґ inserting under pedestals or by shifting of the foundation wedges in couple side position by shifting by means of hydraulic jacks. § Scaffolding erection in necessary range. Carrying out of the tightness welds and screwsґtightening by the prescribed torque. § Dismantling of scaffolding. Check of the casing level and of the proper contact of pedestals to casing. § Assembly of screws into the parting plane, preparation for putting of inner parts inside (washing of preservation, greasing of grooves for gland bodies… ). Date: 12.11.2013 Page 105 / 278 Prepared: O.Baroch Last Revision: Approved:
P.Lešetickэ § Check of slinging equipment and providing of OHS measures for handling with heavy parts § Kontrola vázacích prostředků a zajištění § opatření BOZP pro manipulaci s těžkými díly. Vytvoření obratiště = zabezpečený prostor pro otáčení komponent při zavěšení na hlavní a pomocný zdvih mostového jeřábu strojovny § Creation of turning place = providing of the safe space for turning components while they are fully hung on the main and the auxiliary lift of overhead crane of machine hall § § Providing of OHS measures for assembly of the manoeuvre equipment with its supporting structure (local limitation of assembly works in machine hall).
§ § Zajištění opatření BOZP pro montáž manévrovacího zařízení a jeho podpěrných konstrukcí (lokální omezení montážních prací ve strojovně). § Příprava pro zavezení VT tělesa § Inspection of the documentation of contractor who provides the handling with HP casing (static calculation, licence of operators, revision sheets of the equipment, risk analysis and measures for the risk minimize, etc). Load test of manoeuvre equipment. § Kontrola dokumentace dodavatele provádějícího manipulaci s VT tělesem (statický výpočet, oprávnění obsluhy zařízení, revizní listy zařízení, rozbor rizik a opatření na jejich minimalizaci, atd). Provedení zatěžovací zkoušky