Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika greasing). 8) The first alignment of rotorsґ catenary promazбnн). 8) Prvnн vyrovnбnн rotorovй soustavy § Preparation of the lifting beams: un-wrapping, preservation washing off, greasing of the sliding surfaces, setting of position of suspensions, assemble with ropes. § Releasing of LP rotor from the transport stand, hanging of rotor on the lifting beam, tuning of the rotor level, lifting of the rotor and its moving into bearings.
§ A lignment of rotorsґ catenary into deflection curve according to measurement of mutual rotorsґ position in couplings of LP rotor with HP and IP rotor and rotor of generator. § Checking of clearance and contact of collar of HP and IP rotorto segments of the thrust bearing according the instruction Q159150. § Correcting of the bearingsґposition and slope of bearing stands is done by change on the supporting wedges under pedestals of bearing stands. § Taking of LP rotor out 9) Assembly of the LP diaphragms § Inserting of diaphragms into the bottom part of LP middle casing and bottom parts of gland bodies into bottom part of LP outer casing, taking of the labyrinth segments out.
10) Setting of mutual position of components in the turbine steam flow path (radial and axial setting) § Dummy shaft putting into bearing and radial position of bottoms of LP casings setting against the dummy shaft. § Inserting of rotor, measurement of rotorsґ catenary alignment in couplings, , setting of the tilt of bearing stands § Taking out the LP rotor, correcting of position of, checking of rotorsґ alignment in couplings. § Carrying out of VPL measuring for comparison of values with values from pre-assembly in producing plat. Repair of the found deviations. § Continuous inserting and taking out of the § Přнprava zvedacн ch trave rz:
vybalenн, smytн konzervace, promazбnн kluznэch ploch, nastavenн polohy zбvěsů, skompletovбnн s lany. § Uvolněnн NT rotoru z dopravnнho stojanu, zav ěšenн rotoru na zvedacн traverzu , doladěnн rotoru do vodorovnй polohy, zvednutн rotoru a jeho vloženн do ložisek. § Vyrovnбnн rotorovй soustavy do průhybovky podle měřenн vzбjemnй polohy rotorů ve spojkбch NT rotoru s VT a ST rotorem a rotorem generбtoru. § Kontrola vůle a dosedбnн nбkružku VT a ST rotoru na segmenty axiбlnнho ložiska dle nбvodky Q159150. § Oprava vэškovй polohy ložisek a nбklonu ložiskovэch stojanů se provбdн změnou na podpěrnэch klнnech pod kozlнky ložiskovэch stojanů. § Vyjmutн NT rotoru.
9) Montбž NT rozvбděcнch kol § V loženн spodků rozvбděcнch kol do spodku NT střednнho tělesa a spodků těles ucpбvek do spodku NT vnějšнho tělesa, vyjmutн labyrintovэch segmentů . 10) Ustavenн vzбjemnй polohy dнlů průtočnй čбsti turbiny (radiбlnн a axiбlnн vyrovnбnн) § Vloženн kontrolnн hřнdele do ložisek a radiбlnн vyrovnбnн spodků NT tělesa vůči kontrolnн hřнdel i. § Vloženн NT rotoru, měřenн vyrovnбnн rotorovй soustavy ve spojkбch , nasta venн nбklonu ložiskovйho stojanu § Vyjmutн rotoru, oprava polohy ložisek, kontrola vyrovnбnн rotorovй soustavy ve spojkбch. § Provedenн měřenн VPN pro porovnбnн hodnot s hodnotami z kontrolnн montбže ve vэrobě. Oprava z jištěnэch odchylek.
§ Průběžnй vklбdбnн a vyjнmбnн kontrolnнho Date: 12.11.2013 Page 107 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ § Check of documentation and condition of the lifting beam and slinging means. Providing of OHS measures for handling with heavy parts § Kontrola dokumentace a stavu zvedací traverzy a vázacích prostředků. Zajištění opatření BOZP pro manipulaci s těžkými díly. § Check of slinging equipment and providing of OHS measures for handling with heavy parts § Kontrola vázacích prostředků a zajištění opatření BOZP pro manipulaci s těžkými díly.