Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika dummy shaft and LP rotor. Achieving of radial and axial alignment in open state ATTENTION: hřнde le a NT rotoru. Dosaženo radiбlnнho i axiбlnнho vyrovnбnн v otevřenйm stavu . UPOZORNĚNH: V přнpadě, že by při poklбdбnн dнlů turbiny na pozici byly zjištěny enormnн rozdнly v pružnй deformaci NT tělesa (v porovnбnн s před - montбžн u vэrobce), může nastat nutnost provedenн takzvanйho „Měřenн centricity dнlů průtočnй čбsti v zavřenйm stavu“ a ověřenн vэslednйho vyrovnбnн dнlů metodou nбplastн.
Uvedenй činnosti jsou spojeny s přнpravnэmi pracemi, opakovanэm vklбdбnнm a vyjнmбnнm rotoru, se zavнrбnнm a otevнrбnнm těles a na staveništi se obvykle neprovбdн , je však nutno, aby subdodavatel zajišťujнcн provedenн montбžnнch pracн vzal v ъvahu možnost vэskytu popsanэch pracн. 11) Montбž těles VT a ST RZR ventilů If a huge differences of flexible deformation of LP casing (in comparison with the pre-assembly at producer), it would be necessary to carry ou so-called “Measuring of concentrity of steam flow path elements in closed state” and verifying of the final sett ing of componentsґ position by methods of plasters.
These activities means to carry out the preparation works, repeatedly insert and take out the rotor, repeatedly box up and open the casings. Above described activities are not usually done on site, but it is necessary that the sub-contractor who provides the site assembly works takes in account the posibility of arising of described works. 11) Assembly of bodies of HP and IP SC valves (turbine Stop and control valves) (rychlozбvěrnй a regulačnн ventily turbiny) § Přнprava vzpěr včetně fixačnнch objнmek , provizornн podepřenн vzpěr v kolmй poloze k hornн zбkladovй desce.
§ Vybalenн a přнprava těles VT a ST RZR ventilů na montбž (kontrola stavu po dopravě, mytн konzervace, promazбnн, kontrola vůle v uloženн kulovэch čepů, atd) . § Zavěšenн těles VT a ST RZR ventilů na jeřбb. Zvednutн těles , jejich otočenн z dopravnн do montбžnн polohy s opнrбnнm hrdel pro připojenн potrubн o hornн zбkladovou desku (podloženн dřevěnэmi trбmy), vyrovnбnн . § Zavezenн těles VT a ST RZR ventilů na vzpěry a zafixovбnн jejich polohy na pozici pomocн fixačnнch objнmek. Zajištěnн polohy vzpěr přistehovбnнm přнložek. § Montбž servopohonů, čidel měřenн a potrubн VT hydraulickй regulace.
§ Přнprava těles ventilů na připojenн potrubн (pбra a odvodněnн) a vykonбnн tlakovэch zkoušek na potrubн včetně vyjmutн vnitřnнch dнlů RZ ventilu a instalace vestaveb. § Preparation of the struts including the fixture- sleeves, provisory supporting of the struts in the perpendicular position against to the top foundation slab. § Unwrapping and preparation of bodies of HP and IP SC valves for assembly (checking of condition after transport, preservation washing off, greasing, checking of clearance in the fit of ball journals, etc). § Hanging of the bodies of HP and IP SC valves on a crane.
Lifting of the bodies, their turning from transport position to assembly position with touching of their pipe-sockets to the top foundation slab (supporting by wooden beams), level setting. § Moving of the bodies of HP and IP SC valves on the struts, locking their position by means of the fixture-sleeves. Locking the position of struts by tack-welding of splice-bars. § Assembly of servomotors, sensors of instrumentation and piping of HP hydraulic control systйm. § Preparation of the valvesґ bodies for the piping connecting (steam and drainage) and for the proceeding of pressure tests on piping including the taking the internals from Stop valve out and installation of in-built provisories.
Date: 12.11.2013 Page 108 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ § Check of slinging equipment and providing of OHS measures for handling with heavy parts § Kontrola vázacích prostředků a zajištění opatření BOZP pro manipulaci s těžkými díly