DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika then the anti-sizing compound Molykote G Rapid+ onto all contact (sliding) surfaces between supports and LP casing footings · Clean up and degrease the horizontal and vertical parting plane of casing carefully. · Insert the front bottom LP outer casing (closer to IP turbine part) ensure position against bearing support according to drawing Tp6071672 (detail A-A, B-B). · Insert the rear bottom LP outer casing.

Put down with respect to clearence to middle part of turbine · Build up scaffolding between front and rear LP casing with respect to access to place for assembly. Install safety rail on parts and cover of inlets for piping of gland & vent systйm. · Insert middle bottom LP outer casing between front and rear bottom LP outer casing. · Assembly middle bottom LP outer casing to front bottom LP outer casing. Bolts and nuts pos. 14,15 according drawing Tp6072400 (detail D5), pins pos. 58. · Assembly rear bottom LP casing to middle bottom LP casing. Assembly bolts and nuts pos. 14, 15 according drawing Tp6072400 (detail D5), pins pos. 58.

Ensure the position of bottom LP casing to bearing supports according drawing Tp6071672 (detail A-A, B-B). s kozlнky (včetně per) naneste nejprve kluznэ lak Molykote D321R a pak mazacн pastu Molykote G Rapid+ · Očistěte a důkladně odmastěte horizontбlnн a vertikбlnн dělнсн rovinu tělesa · Vložte přednн čбst NT spodku tělesa (blнže k ST turbнně) zajistěte polohu vůči kozlнku dle vэkres u Tp6071672 (detail A-A, B-B). · Vložte zadnн čбst NT spodku tělesa , tak aby byl prostor pro uloženн střednн čбsti s vůlн. · Montujte l ešenн do prostoru mezi přednн a zadnн čбst spodku NT tělesa s ohledem na přнstupnost mнst montбže.

Instalujte bezpečnostnн zбbradlн na dнly a zakryjte vэvrty pro potrubн komнnkovй a ucpбvkovй pбry. · Mezi přednн a zadnн čбst spodku NT vnějšнho tělesa vložte střednн čбst NT spodku tělesa . · Montujte střednн čбst k přednн čбsti NT spodku těles. Š rouby a matice poz. 14, 15 na vэkrese Tp6072400 (detail D5) , kolнky poz.58. · Přirovnejte zadnн NT spodek tělesa ke střednн čбsti NT spodku tělesa . Montujte šrouby a matice poz. 15, 14 na vэkrese Tp6072400 (detail D5) , kolнky poz. 58. Nбsledně zajistěte polohu vůči kozlнkům podlй vэkresu Tp6071672 (detail A-A, B-B). Attention:

Turning with components of turbine casing on crane is operation with high risk of the personal injury, casing’s damage, crane’s damages and damage of other devices in the machine hall. It is necessary to apply the safety precautions and to avoid access of unauthorized persons into assembly zone always before moving or turning casing. The handling has to be always approved by responsible safety technician Upozorněnн: Otбčenн dнlů těles turbiny na jeřбbu je pracн se zvэšenэm rizikem ъrazu osob, poškozenн těles, poškozenн jeřбbu a jinэch zařнzenн strojovny.

Před otбčenнm a převбženнm tělesa je vždy nezbytnй zajistit provedenн přiměřenэch bezpečnostnнch opatřenн a zamezit vstupu nepovolanэch osob do montбžnн zyny! Provedenн manipulace musн bэt předem schvбleno zodpovědnэm bezpečnostnнm Date: 12.11.2013 Page 143 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ