Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika in advance! Moving of persons under hung casing is strictly prohibited. Allowed ways of handling and turning with turbine casings by means of crane are specified in annex 1. technikem! Pohyb osob pod zavěšenэm tělesem je přнsně zakбzбn. Povolenй způsoby manipulace a otбčenн s tělesy turbiny pomocн jeřбbu jsou specifikovбny v přнloze 1. Notice: Carry out the turning on the turning place (see “Assembly of walls of bottom part of LP outer casing” above) and obey the same principles. For the turning, use the auxiliary lift of overhead crane of machine hall.
Poznбmka: Otočenн proveďte na obratišti (viz. „Montбž stěn spodku vnějšнho NT tělesa“ vэše) a dodržujte stejnй zбsady BOZP. Pro otočenн využijte pomocnэ zdvih jeřбbu strojovny. · Vertically level of the bottom outer LP casing according to the horizontal parting plane which has the same level as turbo-set axis ( level +9,920 m ), after the relief tighten again the bolts M42x3 (poz. 15) up to the touching of the vertical parting planes, lightly tighten these bolts.
· Put the dummy shaft into the bearings of LP rotor (the position of the LP bearing was already set according to deflection curve of rotors’ catenary), carry out the measuring of radial leveling of bottom outer LP casing in bores and correct the position of the bottom part of casing. · Set the level of the horizontal parting plane of the bottom outer LP casing with tolerances of ±0,05 mm , check the contact with the pedestals in entire length by feeler gauge (the local gap must not exceed 0,07 mm ), tighten the anchore bolts of the pedestals at the same time on the pre-described torque:
carry out the lifting and letting the parts of LP casing down by hammering to foundation wedges or their releasing, measure the level by hose water level, water level, T-square 3 m long and by optic or laser leveling. Set the transverse and longitudinal slopes of the horizontal parting plane according to values written in Turbine Dozier book, check it by the water level. · Check the foundation wedges they have to be in mesh (pedestal foundation wedge). Use feeler gauge and knocking · Spodek NT vnějšнho tělesa vэškově vyrovnat v horizontбlnн dělнсн rovin ě , kterб je totožnб s osou stroje ( ъroveň +9 ,920 m ), po nadlehčenн, přitбhnout zpět pomocн šroubů M42x3 (poz.
15) na do tyk vertikбlnнch dělнcнch rovin, šrouby lehce dotбhnout. · Vložte kontrolnн hřнdel do ložisek NT rotoru (poloha ložisek NT byla již ustavena do průhybovky rotorovй soustavy), proveďte měřenн radiбlnнho vyrovnбnн spodku vnějšнho NT tělesa ve vэvrtech a upravte polohu spodku tělesa. · Vyrovn ejte přesně horizontбlnн dělнсн rovinu spodku NT vnějšнho tělesa v toleranci ±0,05 mm , kontrolujte styk s kozlнky v celй dйlce spбroměrkou (lokбlnн vůle nesmн překročit hodnotu 0,07 mm ) současně dotahujte kotevnн šrouby NT kozlнků na předepsanэ utahovacн moment:
zvedбnн a spouštěnн čбstн NT tělesa provбdějte podbнjenнm nebo uvolněnнm zбkladovэch klнnů, měřenн hadicovou vodovбhou, vodovбhou, přнložnэm pravнtkem o dйlce 3 m a nivelacн. Přнčnй a podйlnй sklony horizontбlnн dělнсн roviny nastavte dle hodnot uvedenэch v Pasportu turbiny, kontrolujte vodovбhou. · Kontrolujte zбkladovй klнny musн bэt v zбběru (kozlнk – zбkladovэ klнn ) . Použijte spбroměrku a poklep. · Check the proper contact of LP casings with pedestals by means of the feeler gauge with thickness 0,07 mm . Provide proper contact of the surfaces by knocking to the foundation wedges after releasing of the foundation bolts. Tighten foundation bolts again up to the minimum torque.
· Kontrolujte spбroměrkou 0,07 mm dosedбnн dнlů NT tělesa na kozlнky. Zajistěte důkladnй dosedбnн ploch doklepnutнm zбkladovэch klнnů po uvolněnн zбkladovйho šroubu. Zбkladovэ šroub opět dotбhněte na minimбlnн utahovacн moment. Date: 12.11.2013 Page 144 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ