Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika during pre-assembly in workshop of turbine producer). Measure the correction for setting of axial position of LP casing inside the outer casing: distance of faces of collar of IP rotor in hollow for the thrust bearing in rear HP bearing stand and axial clearances in steam flow path (measurement with the wedge-gauges). · Take LP rotor out. Put the dummy shaft into bearings.
Evaluate the influence of deformation of the foundation after loading of foundation with the weight of the rotor and compare it with the measuring from the preassembly which was done in workshop of producer and carry out the correction of position of LP casing against the dummy shaft. · It is possible to correct the radial position of stator parts by changing of the suspension pads thickness of diaphragms. There is the spare set of suspension-pads in delivery with allowance for machining at the site. Side correction of diaphragms are not carry out, setting of side position can be solved by changing of rotor position in bearing vans.
· Carry out VPL measurement to find out the right setting of radial inner parts in the bottom outer casing. Compare the results with values measured in producer workshop and correct the found deviations . Put in the dummy shaft and carry out the final correction of radial setting of stator parts based on evaluation of described measurements. Take out the dummy shaft. Notice: Usually it is not necessary to carry out VPL measurement. DSPW supervision staff on site will decide about VPL necessity with respect to the actual state. · Leveling state:
Diaphragms are radially set now (vertically and laterally) with accuracy better then 0,1 mm in comparison with the measuring in open state carried out during preassembly in DSPW workshop. It is not necessary to set the gland’s bodies, they are fixed in grooves of turbine casing. Mentioned setting of the radial position of parts is carried out with taking respect to: vэrobce). Změřte takй korekci pro ustavenн axiбlnн polohy NT tělesa porovnбnн vzdбlenost i čel nбkružku ST rotoru ve vybrбnн pro axiбlnн ložisko v zadnнm VT ložiskovйm stojanu a axiбlnнch vůlн v průtočnй čбsti (měřenн pomocн klнnovэch měrek). · Vyjměte NT rotor a v ložte kontrolnн hřнdel do ložisek.
Vyhodnoťte vliv deformace zбkladu po zatнženн hmot ou rotoru v porovnбnн s měřenнm během před - montбže v dнlně vэrobce a proveďte korekci polohy NT tělesa vůči kontrolnн hřнdeli. · Korekce radiбlnн polohy statorovэch dнlů je možnй provбdět: změnou tloušťky podložek zбvěsů rozvбděcнch kol. V dodбvce turbiny je sada nбhradnнch podložek zбvěsů rozvбděcнch kol s přнdavkem na opracovбnн na staveništi. Stranovй korekce rozvбděcнch kol se neprovбdějн, vyrovnбnн lze zajistit změnou polohy rotoru v l ožiskovэch vanбch. · Proveďte měřenн VPN pro zjištěnн sprбvnйho nastavenн radiбlnн polohy spodku vnitřnнho dнlů NT tělesa .
Porovnejte vэsledek s hodnotami naměřenэmi v dнlně vэrobce a zjištěnй odchylky opravte . Vložte kontrolnн hřнdele a proveďte finбlnн kontrolu nebo ъpravy v radiбlnнm ustavenн statorovэch dнlů na zбkladě vyhodnocenн popsanэch měřenн. Vyjměte kontrolnн hřнdel. Poznбmka: M ěřenн VPN nenн obvykle nutno provбdět. O nutnosti VPN r ozhodne montбžnн dozor DSPW na staveništi s ohledem na aktuбlnн sta v. · Stav vyrovnбnн: Rozvбděсн kola jsou nynн radiбlně ustavena (vэškově a stranově) s přesnostн lepšн než 0,1 mm v porovnбnн s měřenнm v otevřenйm stavu provбděnйm při kontrolnн montбži v dнlně DSPW . Tělesa ucpбvek nenн třeba ustavovat, poloha ucpбvek je pevně fixovбna v drбžkбch tělesa.
Uvedenй ustavenн radiбlnн polohy dнlů je provedeno s ohledem na: Ш The journal position changing in bearing Ш změnu polohy ložiskovйho čepu v ložisku po after turbine start up Ш the displacements araising during LP casing boxing up (measured during preassembly in workshop of producer or on site during boxing up against the dummy shaft, as described above) najetн turbiny Ш na posuvy, kterй vznikajн při zavнrбnн NT těles (odměřeno při kontrolnн montбži v dнlnбch vэrobce nebo na staveništi při zavнrбnн těles vůči kontrolnн hřнdelн uvnitř, jak je popsбno vэše) Date: 12.11.2013 Page 157 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ