DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika · Modify the axial position of the set: rear IP bearing stand HP casing front HP bearing stand so, that the gaps with right dimensions and shape arise between end of traverses and contact surfaces on HP casing are equal for spacers inserting · Set the axial position of LP rotor: either according to axial bearing after inserting of bearing segments and HP and IP turbine rotor or according to recorded distance between the machined surfaces of coupling hub inside the bearing stand from preassembly.

· Carry out setting by changing of the front bearing stand position (shifting) in the slide guiding of pedestal and by moving with whole HP casing. · Put the stones into thrust bearing and push HP casing so that HP rotor touches stones on the active side of axial bearing · Check LP outer casing axial position against to coupling hub face of HP andb IP rotor or correct the turbo-set position (it is measured the distance between the surface for attachment of the cone of gland and coupling face, according to drw.

= 1273,6 mm ) · Put LP rotor into radial bearings and move it up to contact of both coupling hub faces with IP rotor · Measure the position against rotor (clearance between diaphragms and rotor) according to values written in Turbine Dozier book, determinated the value of corrections of axial setting of LP steam flow path elements, for measuring use the special wedge gauges. · Take out LP rotor and carry out the necessary changes in elements axial setting by shifting of LP outer casing.

· Put the labyrinth segments of shaft glands in LP diaphragms ( pay attention to indication of the labyrinth segments!) · Put LP rotor in, shift it to be in contact with HP and IP rotor which is supported by segments on active side of the thrust bearing. Measure the axial clearances in the turbine steam flow path and among the bottom of HP casing and traverses of bearing stands. Work status: Position of steam turbine is set in axial direction. Casings are ready for steam piping assembly without connecting to the casings, for setting of spring’s supports of condenser and · U pravte axiбlnн polohu soustavy:

zadnн VT ložiskovэ stojan – VT těleso – přednн VT ložiskovэ stojan tak, aby mezi konci traverz a dosedacнmi plochami na spodku VT tělesa vznikly mezery odpovнdajнcн rozměrům a tvarům dodanэch mezikusů · Nastavte axiбlnн polohu NT rotoru: buďto podle axiбlnнho ložiska po vloženн segmentů axiбlnнho ložiska a VT a ST rotoru turbiny nebo podle nбměru vzdбlenosti spojkovйho kotouče od opracovanй plochy uvnitř ložiskovйho stojanu z kontrolnн montбže. · Ustavenн proveďte změnou polohy (posuvem) přednнho ložiskovйho stojanu v kluznйm vedenн kozlнku a posuvem celйho VT tělesa.

· Vložte kameny do axiбlnнho ložiska a natlačte VT těleso tak, aby se VT rotor dotэkal kamenů aktivnн stran y axiбlnнho ložiska. · Kontrolujte axiбlnн polohu NT vnějšнho tělesa vůči čelu spojkovйho kotouče VT a ST rotoru, přнpadně korigujte polohu soustavy (měřena vzdбlenost mezi plochou pro upevněnн kužel u ucpбvky – čelo spojky, dle vэkresu = 1273,6 mm ) · Vložte NT rotor do radiбlnнch ložisek a přesuňte jej na dotyk obou čel spojkov эch kotoučů s e ST rotorem. · Odměřte axiбlnн polohu vůči rotoru (vůle mezi rozvбděcнmi koly a rotorem) dle hodnot uvedenэch v pasportu turbiny, určete hodnoty korekc н v axiбlnнm ustavenн dнlů NT průtočnй čбsti, pro měřenн použijte speciбlnн klнnovй měrky.

· Vyjměte NT rotor a proveďte potřebnй změny v axiбlnнm ustavenн dнlů posunem v nějšнho NT tělesa . · Vložte labyrintovй segmenty hřнdelovэch ucpбvek NT rozvбděcнch kol ( pozor na označenн labyrintovэch segmentů! ). · Vložte NT rotor, natlačte jej na VT a STrotor, kterэ se opнrб o segmenty na aktivnн straně axiбlnнho ložiska. Proměřte axiбlnн vůle v průtočnй čбsti turbiny a mezi spodkem VT tělesa a traverzami ložiskovэch stojanů. Stav pracн: P arnн turbina je axiбlně vyrovnбna. Tělesa turbiny jsou připravena pro montбž potrubн bez připojenн k tělesům turbiny , pro nastavenн předpětн pružinovэch podpěr kondenzбtoru a Date: 12.11.2013 Page 163 / 278 Prepared: O.Baroch Last Revision: Approved:

P.Lešetickэ