DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika front bearing stand and bottom of outer casing. Compare the readings with the measuring in article „Leveling and axial positioning of the bottom part of turbine casing“ and with recorded values in Turbine Pasport book, make a corrections if needed. · Take out the labyrint segments of the shaft glands (gland bodies and diaphragms). · Put the check shaft with rings ( Tp6071233 ) into bearings and measure the radial position of inner parts against the shaft while the casing is openned up to parting plane.

· Assemble guiding rods ( Tp527698 ) to parting planes of casings and carriers (outer casing, inner casings, carriers). · Casing closing carry-out in order to measurement of correction for alignment centricity in closed state on control check · Assemble step by step the upper halves of inner parts and at the end put the cover of IP outer casing on bottom. Tighten slightly the screws of the parting plane only to be the surfaces in proper contact (check it with feeler gauges with thickness of 0,02 up to 0,05 mm). Follow the instructions for measurement written in text below.

· During the boxing up, measure the radial position changes between the stator parts against the check shaft on the accessible places by means of the inside micrometer (bore of the bearing stands and casings, grooves of diaphragms and gland bodies). · During the boxing up, measure the gap of parting planes on casings and carriers in free state before the screw tightening. · Open the boxing into parting planes and repeate the meassurement by this procedure · Compare meassured vaules of corrections with theoretical values and set up the difference for parts line-up on the concrete foundation · Open the outer casing up to the parting plane.

Check the dilatation clearances measure the thickness of deformed lead wire. · Compare the readings of radial centricity measurement to the check shaft with the record in Turbine Pasport book. If the differences are less then 0,2 mm, continue. If any difference reaches or exceeds 0,2 mm ložiskovэch stojanů a spodku tělesa. Hodnoty porovnejte s měřenнm v předchozн kapitole a s hodnotami uvedenэmi v Pasportu turbiny a proveďte přнpadnй korekce vyrovnбnн. · Vyjměte veškerй labyrintovй segmenty z hřнdelovэch ucpбvek (ucpбvky i rozvбděсн kola). · Vložte kontrolnн hřнdel s kroužky ( Tp6071233 ) do ložisek a proveďte odměřenн radiбlnнho vyrovnбnн spodků v otevřenйm stavu na kontrolnн hřнdel.

· Montujte vodнcн svнčky ( Tp527698 ) do dělнcнch rovin těles a nosičů (vnějšн těleso, vnitřnн tělesa, nosiče) · Proveďte zavřenн tělesa za ъčelem naměřenн korekcн pro ustavenн centricity v zavřenйm stavu na kontrolnн hřнdel · Montujte postupně hornн čбsti všech vnitřnнch dнlů a nakonec zavřete vнko vnějšнho ST tělesa. Šrouby dělнcнch rovin utahujte vždy pouze na dosednutн stykovэch ploch (kontrola spбroměrkou 0,02 až 0,05 mm). Měřte hodnoty korekcн pro ustavenн centricity statorovэch dнlů v uzavřenйm stavu na kontrolnн hřнdel nбsledovně.

· Během zavнrбnн proměřujte odpichem změny polohy statorovэch dнlů vůči kontrolnн hřнdeli na přнstupnэch mнstech (vэvrty ložiskovэch stojanů a těles, drбžky rozvбděcнch kol a těles ucpбvek). · Během zavнrбnн těles proměřujte spбroměrkou dosedбnн dělнcнch rovin těles a nosičů ve volnйm stavu před utaženнm šroubů. · Otevřete těleso do dělнсн roviny a přitom opakujte měřenн. · Porovnejte naměřenй velikosti korekcн s hodnotami uvažovanэmi při kontrolnн montбži a stanovte rozdнl pro vyrovnбnн dнlů na betonovйm zбkladě. · Otevřete vnějšн těleso do dělнсн roviny. Kontrolujte dilatačnн vůle odměřenнm tloušťky deformovanйho olověnйho drбtu.

· Porovnejte naměřenй hodnoty radiбlnнho vyrovnбnн na kontrolnн hřнdel s hodnotami v Pasportu turbiny. Pokud se hodnoty nelišн vнce než o 0,2 mm pokračujte. Pokud se hodnoty lišн o 0,2 mm a vнce – proveďte Date: 12.11.2013 Page 173 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ