Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika change the position of the relevant stator parts. Attention: take into account difference of outer bottom casing position during assembly on power plant. · Take the check shaft out and insert the IP rotor into bearings. Check the slopes by means of the level (rotor journals, bearing stands, turbine casing). · Remove the covers of level pegs attached on the turbine outer casing and bearing stands. · Perform measurement by the method of Very precise levelling (VPL). · Take the rotor out of turbine. · Evaluate all results of measurements with check shaft and VPL.
Compare the results with the values recorded in Turbine Pasport book. The differences must not exceed 0,1 mm. In opposite situation is necessary to make the corrections and repeat VPL measuring. The correction of the partґs radial setting can be done as follow: altitude change = change of thickness of the pads in diaphragmґs suspensions (turbine delivery includes the set of spare pads with allowance for itґs machining). Corrections of t he side position are not expected (change of rotor position inside bearing stands).
· If any corrections of the parts position was done, take the bottom parts out, blow the bottom casing and all parts with pressurized air and put the parts back into IP outer casing. · Assemble the labyrinth segments of the shaft glands into the gland bodies and all diaphragm wheels. · Axial setting of the steam flow path elements. · Put the IP rotor into bearings (the thrust bearing is without stones) with respect to the labyrinth segments of glands. Check the position of IP rotor to LP rotor and to HP/IP outer casing. Check of dimensions between the bottom casing and the end of cross beam of front bearing stand.
· Correct the mutual positron of rotor-stator if necessary with shifting of the front IP bearing stand. · Stones into thrust bearing and spacers between the bottom casing and the end of cross beam of front bearing stand assembly. · Clearance and contact of rotor and stones check in the thrust bearing acc. to assembly korekce radiбlnнho vyrovnбnн statorovэch dнlů. Pozor: přihlйdněte k d iferencнm polohy vnějšнho tělesa během montбže na elektrбrně. · Vy jměte kontrolnн hřнdel a vložte ST rotor. Kontrolujte nбklony vodovбhou (ložiskovй čepy, ložiskovй stojany, těleso turbiny). · Odkryjte nivelačnн čepy na tělese a na ložiskovэch stojanech parnн turbiny.
· Proveďte měřenн metodou Velmi přesnй nivelace (VPN). · Vyjměte rotor. · Proveďte vyhodnocenн měřenн na kontrolnн hřнdel a VPN. Zohledněte naměřenй rozdнly ve velikostech korekcн pro centricitu v zavřenйm stavu a porovnejte vэsledky s hodnotami v pasportu turbiny. Vэsledky se nesmн lišit o vнce než 0,1 mm. V opačnйm přнpadě proveďte dodatečnй korekce a měřenн VPN opakujte. Korekce radiбlnнho ustavenн dнlů je možnй provбdět vэškově změnou tloušťky podložek zбvěsů rozvбděcнch kol. V dodбvce DSPW je sada nбhradnнch podložek s přнdavkem na opracovбnн. Stranovй korekce se při montбži na elektrбrně již nepředpoklбdajн (přнpadnб oprava se provede změnou polohy rotoru ve stojanech).
· Pokud byly provбděny nějakй korekce v ustavenн dнlů, demontujte vnitřnн dнly, vyčistěte těleso vyfoukбnнm stlačenэm vzduchem a vložte dнly zpět do spodku vnějšнho ST tělesa. · Namontujte labyrintovй segmenty hřнdelovэch ucpбvek do těles ucpбvek a do rozvбděcнch kol. · Axiбlnн ustavenн vnitřnнch dнlů průtočnй čбsti. · Vložte ST rot or do ložisek s ohledem na labyrintovй segmenty ucpбvek. Kontrolujte pozici ST rotoru vůči NT rotoru a vůči ST tělesu, kontrolujte rozměry mezi tělesem a konci traverzy přednнho ložiskovйho stojanu. · Korigujte odchylky vzбjemnй polohy dнlů posunutнm ST přednнho ložiskovйho stojanu.
· Montujte kameny do axiбlnнho ložiska a mezikusy mezi koncem traverzy a spodkem tělesa. · Kontrolujte vůli a dosedбnн rotoru a kamenů v axiбlnнm ložisku, dle nбvodky Q159150. Date: 12.11.2013 Page 174 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ