DOOSAN ŠKODA POWER — DOOSAN ŠKODA POWER Steam Turbine Assembly Manual

Instructions for ST assembly 210 MW Bandel India Document number: S12003-YK09-05MAA-747002 Tylova 57l 31600 Plzeň l Českб Republika PPP of the inner space of bearing stands as well as all parts closed in the bearing stands is done in scope of PPP of the lubrication & jacking oil system. Preservation means which are applied on components as the surface protection, which are in contact with the oil filling as well as with the seal compounds which are used to seal the oil space must not influence the chemical properties of the oil filling especially its demulsification factor. Wrong selected preservation and seal compounds can deteriorate the oil filling.

DSPW has good experience with preservation CORTEC VpCI- 322 and with seal compound NOVATO TL 350. It is recommended to carry out the flushing by oil or a hydraulic fluid after putting of pedestals into grout (any pollution of concrete foundation stool by the oil would mean that the grout would not connect the concrete properly). Servomotors of hydraulic control system are not subject of PPP; PPP is carry out only on piping of hydraulic liquid distribution. PPP of the steam flow path in the turbine casings is not carried out.

During assemby it is carried out only cleaning and degreasing of contact surfaces, journals of rotors and surface in area where the measurement with the mechanical instruments is done. Preservation means applied onto inner surface of steam flow path are washed down by steam during the putting of the turbine into operation and they will appear as contained in the condensate. That is why the type of preservation is always assessed and approved by the power unit operator.

Preservation means determinated for the long- term storage or the overseas tranposrt (the PČO vnitřnнch prostor ložiskovэch stojanů turbiny a všech dнlů uzavřenэch v ložiskovэch stojanech se provбdн v rбmci PČO systйmu mazacнho & zvedacнho oleje. Konzervačnн prostředky použitй na ochranu povrchu dнlů, kterй jsou ve styku s olejovou nбplnн stejně , jako tmely použitй k zatěsněnн olejovйho prostoru nesmн ovlivnit chemickй vlastnosti olejovй nбplně – zejmйna jejн deemulgačnн čнslo. Nevhodně zvolenй konzervanty a t mely mohou znehodnotit olejovou nбplň. DSPW тб přнznivй zkušenosti s konzervacн CORTEC VpCI -322 a tmelem NOVATO TL tmel 350.

Proplachy olejem nebo hydraulickou kapalinou je doporučeno provбdět až po zalitн kozlнků do betonu (nebezpečн znečištěnн betonu z бkladovй stolice olejem , kterй nбsledně neu možnн sprбvnй napojenн zбlivky). Servomotory hydraulickй regulace nejsou předmětem PČO; PČO se provбdн pouze na potrubн rozvodu hydraulickй kapaliny. PČO parnн průtočnй čбsti těles turbiny se neprovбdн. V průběhu montбže se provede pouze očištěnн a odmaštěnн stykovэch ploch, ložiskovэch čepů rotorů a povrchu v mнstech měřenн mechanickэmi měřidly. Konzervačnн prostředky použitй na vnitřnнm povrchu parnн průtočnй čбsti se smyjн parou během uvбděnн turbiny do provoz u a objevн se obsaženy v kondenzбtu.

Proto druh konzervantu vždy posuzuje a schvaluje provozovatel energetickйho bloku . Konzervanty určenй pro dlouhodobй skladovбnн nebo zбmořskou dopravu (vosk y ) se před montбžн musн odstranit a nahradit lehkou konzervacн ( napřнklad nбhradnн dнly). Date: 12.11.2013 Page 276 / 278 Prepared: O.Baroch Last Revision: Approved: P.Lešetickэ 3 Instructions for proceeding of the post-assembly purge processes and pressure tests / Pokyny k provedení pomontážních čistících operací a tlakových zkoušek 2.14 Instruction for proceeding of the post-assembly purge processes (PPP) / Pokyny k provedení pomontážních čistících operací (PČO)