Western Star — Western Star (EN)

Manual Transmissions and Clutch Eaton Fuller 18-Speed Splitter and Range-Shift Transmissions drive (rearward) position ( Fig. 14.2 ). Double- clutch into 1st gear. Continue upshifting through the shift pattern. Double-clutch when moving the gear shift lever (1st to 2nd to 3rd to 4th); single-clutch during split shifts (1st direct to 1st overdrive, etc.). Eaton Fuller 18-speed transmissions have eighteen forward speeds and four reverse speeds. Each trans- mission consists of a 5-speed front section and a 4-speed auxiliary section. The auxiliary section con- tains low- and high-range ratios, plus a splitter gear. See Fig. 14.2 . 5.

When in 4th overdrive, use the range- preselection lever and the splitter-control button to upshift to 5th gear. 1 While in 4th gear, pull the range-preselection lever up into high range and move the splitter- control button to the low position. Double-clutch into 5th gear, engage the clutch, and accelerate. A 6. Upshift progressively through the high range gears. B To shift from 5th direct to 5th overdrive (or 5th underdrive to 5th direct on RT model transmis- sions), move the splitter-control button to the high position, then immediately release the ac- celerator. Press and release the clutch pedal, and accelerate. 03/13/96 f260157a C D A. High Range B. Low Range C. Overdrive (forward) D.

Direct Drive (rearward) 1. Splitter Control Button Continue upshifting through the shift pattern. Double-clutch when moving the gear shift lever (6th to 7th, etc.); single-clutch during split shifts (6th direct to 6th overdrive, etc.). Fig. 14.2, Eaton Fuller 18-Speed Transmission Shift Pattern LOW gear in the front section is used only as a start- ing gear; it is never used when the transmission is in high range. LOW gear can be split, to provide both a direct and an overdrive ratio. Downshifting IMPORTANT: Never use the clutch brake when downshifting, or as a brake to slow the vehicle. Upshifting 1.

To downshift from 8th overdrive to 8th direct (or 8th direct to 8th underdrive on RT model trans- missions), move the splitter-control button to the low position, then immediately release the accel- erator. Press and release the clutch pedal, then accelerate once the transmission has shifted. 1. Put the transmission in neutral. Start the engine and bring the air system pressure up to 100 to 120 psi (689 to 827 kPa). 2. Position the range-preselection lever down, in low range and make sure the splitter-control but- ton is in the low position. See Fig. 14.2 . 2.

Start the downshift from 8th direct to 7th over- drive by moving the splitter-control button to the high position, then immediately double-clutch into 7th gear. 3. To start the vehicle moving, press the clutch pedal to the floor, shift into LOW, then engage the clutch with the engine at or near idle speed. To shift from LOW direct to LOW overdrive, move the splitter-control button into the overdrive (forward) position, then immediately release the accelerator. Press and release the clutch pedal, and accelerate. 3. Downshift progressively through each of the high range gears, alternating the procedures in steps 1 and 2 above until reaching 5th direct. 4.

When in 4th overdrive, push the range- preselection lever down and move the splitter- control button to the high position. Double-clutch 4. Upshift from LOW overdrive to 1st direct by first moving the splitter-control button into the direct 14.3 5 5 7 R DirOD Dir 1 1 3 DirOD Dir N 6 6 8 DirOD Dir LOWLOW Dir OD 2 2 4 DirOD Dir 7 OD 3 OD 8 OD 4 OD 5 Dir 5 OD 1 Dir 1 OD