Mitsubishi — 1.2 Basic engine

SERVICE DATA Table 2-2 Maintenance service data table - Basic engine(3 / 4) Unit mm [in.] 2-4 Inspection point Nominal Standard Limit Remark Piston Outside diameter L2A L3A STD ø 65 [2.559] 64.919 to 64.939 [2.5559 to 2.5566] 0.25 OS ø 65.25 [2.569] 65.169 to 65.189 [2.5657 to 2.5665] 0.50 OS ø 65.50 [2.579] 65.419 to 65.439 [2.5755 to 2.5763] L2C L3C STD ø 70 [2.756] 69.913 to 69.933 [2.7525 to 2.7533] 0.25 OS ø 70.25 [2.766] 70.163 to 70.183 [2.7623 to 2.7631] 0.50 OS ø 70.50 [2.776] 70.413 to 70.433 [2.7722 to 2.7729] L2E L3E STD ø 76 [2.992] 75.906 to 75.926 [2.9884 to 2.9892] 0.25 OS ø 76.25 [3.002] 76.156 to 76.176 [2.9983 to 2.9990] 0.50 OS ø 76.50 [3.012] 76.406 to 76.426 [3.0081 to 3.0089] Piston pin outside diameter L2A, L3A L2C, L3C ø 18 [0.71] 18.001 to 18.007 [0.7087 to 0.7089] L2E, L3E ø 21 [0.83] 21.002 to 21.005 [0.8269 to 0.8270] Clearance between piston pin bore and piston pin L2A, L3A L2C, L3C 0.006 to 0.018 [0.0002 to 0.0007] 0.08 [0.0031] L2E, L3E 0.007 to 0.015 [0.0003 to 0.0006] Clearance between piston and cylinder (clearance) L2A, L3A 0.061 to 0.111 [0.0024 to 0.0044] 0.2 [0.0079] Repair to oversize or replace L2C, L3C 0.067 to 0.117 [0.0026 to 0.0046] L2E, L3E 0.074 to 0.124 [0.0029 to 0.0049] Piston ring Clearance between ring and ring groove No.1 Compression ring - 0.3 [0.0118] Replace No.2 Compression ring 0.05 to 0.09 [0.0020 to 0.0035] 0.2 [0.0079] Oil ring 0.03 to 0.07 [0.0019 to 0.0028] 0.2 [0.0079] Closed gap of ring No.1 Compression ring 0.15 to 0.30 [0.0059 to 0.0118] 1.5 [0.0591] Replace No.2 Compression ring 0.15 to 0.30 [0.0059 to 0.0118] Oil ring 0.15 to 0.35 [0.0059 to 0.0138] Connecting rod Bend and torsion 0.05/100 [0.0020/3.94] or less 0.15/100 [0.0059/ 3.94] End play 0.10 to 0.35 [0.0039 to 0.0138] 0.5 [0.0197]