Komatsu — STANDARD VALUE TABLE FOR ELECTRICAL PARTS

TESTING AND ADJUSTING STANDARD VALUE TABLE FOR ELECTRICAL PARTS 20-14 Sys- tem Name of component Connector No. Inspec- tion method Judgement table Measurement conditions Control system Engine throttle, pump controller Travel EPC solenoid valve G63 Measure resistance If the condition is as shown in the table below, it is normal Between (1) - (2) 7-14 Ω Between (1), (2) - chassis Min. 1 MΩ 1) Turn starting switch OFF. 2) Disconnect connector G63. Power source voltage C01 C02 Measure voltage If the condition is as shown in the table below, it is normal Between C01, (7), (13) - C01 (6), (12) 20 - 30 V Between C02 (11), (21) - C01 (1), (12) 20 - 30 V 1) Turn starting switch ON.

2) Insert T-adapter. Fuel control dial C03 Measure voltage If the condition is as shown in the table below, it is normal Between (7) - (17) (power source) 4.75 - 5.25 V Between (4) - (17) (low idling) 4.0 - 4.75 V Between (4) - (17) (high idling) 0.25 - 1.0 V 1) Turn starting switch ON. 2) Insert T-adapter. Governor potentiometer C03 Measure voltage If the condition is as shown in the table below, it is normal Between (14) - (17) (power source) Low idling 2.9 - 3.3 V High idling 0.5 - 0.9 V Between (7) - (17) (power source) 4.75 - 5.25 V 1) Turn starting switch ON. 2) Insert T-adapter.

Radiator water temperature signal P07 (male) Measure resistance If the condition is as shown in the table below, it is normal Normal temperature (25°C) Approx. 70-78 kΩ 100°C Approx. 3.5-4.0 kΩ 1) Turns starting switch OFF. 2) Disconnect connector P7. 3) Insert T-adapter into connector at sensor end. Governor motor C02 Measure voltage If the condition is as shown in the table below, it is normal Between (2) - (3) 1.8 - 4.6 V Between (4) - (5) 1.8 - 4.6 V 1) Turn starting switch ON. 2) Insert T-adapter. Battery relay C01 Measure voltage If the condition is as shown in the table below, it is normal Between (1) - (6) 20 - 30 V # This is only for 2.5 sec.

after the starting switch is operated ON  OFF; at other times it must be 0 V. 1) Turn starting switch ON. 2) Insert T-adapter. Between (1) - (2) 7-14 Ω Between (1), (2) - chassis Min. 1 MΩ Between C01, (7), (13) - C01 (6), (12) 20 - 30 V Between C02 (11), (21) - C01 (1), (12) 20 - 30 V Between (7) - (17) (power source) 4.75 - 5.25 V Between (4) - (17) (low idling) 4.0 - 4.75 V Between (4) - (17) (high idling) 0.25 - 1.0 V Between (14) - (17) (power source) Low idling 2.9 - 3.3 V High idling 0.5 - 0.9 V Between (7) - (17) (power source) 4.75 - 5.25 V Normal temperature (25°C) Approx. 70-78 kΩ 100°C Approx.

3.5-4.0 kΩ Between (2) - (3) 1.8 - 4.6 V Between (4) - (5) 1.8 - 4.6 V Between (1) - (6) 20 - 30 V