Freightliner FLD Conventional — FLD Conventional

Transmissions 5. Double-clutch between all upshifts and down- shifts. move the shift lever to the next desired gear po- sition. 6. After your shifting ability improves, you may want to skip some of the ratios. This may be done only when operating conditions permit, depend- ing on the load, grade, and road speed. The combination button/lever shift is used for gear changes from 2nd to 3rd, 4th to 5th, 6th to 7th and 8th to 9th. Downshifting 7. Avoid hunting for neutral by moving the gear shift lever from the left rail to right rail. This action can cause excessive transmission wear.

CAUTION Upshifting Do not attempt a button-only downshift at too high an engine speed (generally above 1400 rpm). Doing so could result in damage to the en- gine, transmission, and/or driveline. 1. Position the gear shift lever in neutral. Start the engine, and bring the air system pressure up to 100 to 120 psi (689 to 827 kPa). 1. Button-only shift—With the throttle still applied, preselect the next gear by sliding the shift button rearward. Break torque by releasing the throttle or by depressing the clutch pedal. Increase en- gine speed to synchronize the engine speed with the transmission speed. The shift will complete when the engine rpm has increased to the proper speed. 2.

Depress the clutch pedal to the floor. Shift into 1st gear, then engage the clutch, with the engine at or near idle speed, to start the vehicle moving. 3. Button-only shift—Preselect the next gear by sliding the shift button forward. Break torque by releasing the throttle or by depressing the clutch pedal. Decrease engine speed to synchronize the engine speed with the transmission speed. The shift will complete when the engine rpm has decreased to the proper speed. The button-only shift is used for gear changes from 10th to 9th, 8th to 7th, 6th to 5th, 4th to 3rd, and 2nd to 1st.

The button-only shift is used for gear changes from 1st to 2nd, 3rd to 4th, 5th to 6th, 7th to 8th, and 9th to 10th. CAUTION Do not attempt a lever-only downshift at too high an engine speed (generally above 1000 rpm). Doing so could result in damage to the engine, transmission, and/or driveline. 4. Lever-only shift—Break torque by releasing the throttle and depressing the clutch pedal. Double- clutching, move the shift lever to the next desired gear position. Decrease engine speed to syn- chronize the engine speed with the transmission speed. The shift will complete when the engine rpm has decreased to the proper speed. 2.

Lever-only shift—Break torque by releasing the throttle and depressing the clutch pedal. Double- clutching, move the shift lever to the next desired gear position. The lever-only shift is used to skip a full gear. With the shift button rearward—1st to 3rd, 3rd to 5th, 5th to 7th, and 7th to 9th. With the shift but- ton forward—2nd to 4th, 4th to 6th, 6th to 8th, 8th to 10th. The lever-only shift is used to skip a full gear. With the shift button rearward—9th to 7th, 7th to 5th, 5th to 3rd, and 3rd to 1st. With the shift but- ton forward—10th to 8th, 8th to 6th, 6th to 4th and 4th to 2nd. NOTE:

Lever-only shifts skip an entire gear ratio and will require the engine rpm to decrease twice the amount of a normal shift. IMPORTANT: Never use the clutch brake when downshifting, or as a brake to slow the vehicle. 5. Combination button/lever shift—Preselect the next gear by sliding the shift button rearward. Break torque by releasing the throttle and de- pressing the clutch pedal. Double-clutch and CAUTION Do not attempt a combination button/lever down- shift at too high an engine speed (generally 8.12