Section 5B EFI Fuel System The oxygen sensor can function only after being heated by exhaust temperatures to a minimum of 375°C (709°F). A cold oxygen sensor will require approximately 1-2 minutes at moderate engine load to warm sufficiently to generate a voltage signal. Proper grounding is also critical. The oxygen sensor grounds through the metal shell, so a good, solid, unbroken ground path back through the exhaust system components, engine, and wiring harness is required. Any disruption or break in the ground circuit can affect the output signal and trigger misleading fault codes. Keep that in mind when doing any troubleshooting associated with the oxygen sensor.
The oxygen sensor can also be contaminated by leaded fuel, certain RTV and/or other silicone compounds, carburetor cleaners, etc. Use only those products indicated as “O 2 Sensor Safe.” quickly and check the reading again. If voltage momentarily increases and then again declines, without cycling, engine may be running lean due to incorrect TPS initialization. Shut off the engine, perform TPS initialization, and then repeat the test. If TPS initialization cannot be achieved, perform step c. c. Replace the oxygen sensor (see next page). Run the engine long enough to bring the new sensor up to temperature and repeat the output test from step 1.
The cycling voltage from 0.2 to 1.0 volt should be indicated. 2. Move the black voltmeter lead to the engine ground location and repeat the output test. The same voltage ( 0.2 v-1.0 v ) should be indicated. Service Like the other sensors already discussed, the oxygen sensor is a non-serviceable component. Complete replacement is required if it is faulty. The sensor and wiring harness can be checked as follows. a. If the same voltage reading exists, go on to step 3. b. If the voltage output is no longer correct, a bad ground path exists between the sensor and the engine ground.
Touch the black lead at various points, backtracking from the engine ground back toward the sensor, watching for a voltage change at each location. If the correct voltage reading reappears at some point, check for a problem (rust, corrosion, loose joint or connection) between that point and the previous checkpoint. For example, if the reading is too low at points on the crankcase, but correct voltage is indicated when the black lead is touched to the skin of the muffler, the flange joints at the exhaust ports become suspect. NOTE: All tests should be conducted with a good quality, high-impedance, digital VOA meter for accurate results. 1. Oxygen sensor must be hot (minimum of 400°C, 725°F).
Run engine for about 5 minutes. With the engine running, disconnect the oxygen sensor lead from the wiring harness. Set VOA meter for DC volts and connect the red lead to the disconnected sensor lead, and the black lead to the sensor shell. Check for a cycling voltage reading between 0.2 and 1.0 volt . a. If voltage is in the specified range, go to step 2. 3. With sensor still hot (minimum of 400°C, 752°F), switch meter to the Rx1K or Rx2K scale and check the resistance between the sensor lead and sensor case. It should be less than 2.0 K Ω . b. If the voltage is not in the specified range, reconnect the oxygen sensor lead.
With the lead connected, probe or connect the sensor connection with the red VOA meter lead. Attach the black VOA meter lead to a known good ground location. Start and run the engine at 3/4 throttle and note the voltage output. a. If the resistance is less than 2.0 K Ω , go to step 4. b. If the resistance is greater than 2.0 K Ω , the oxygen sensor is bad, replace it. The reading should cycle between 0.2 and 1.0 volt, which indicates the oxygen sensor is functioning normally and also the fuel delivery controlled by the ECU is within prescribed parameters. If the voltage readings show a steady decline, bump the governor lever to make the engine accelerate very 4.
Allow the sensor to cool (less than 60°C, 140°F) and retest the resistance with the meter set on the Rx1M scale. With the sensor cool, the resistance should be greater than 1.0 M Ω . 5B.10