Aegis LH630-775 — Section 5B - EFI Fuel System

Terninal Red PID Spork Terninal Block Plug Spork Plug Cylinder #2 ¢J1-309 Cylinder #1 Terninal Red P2: SWITCH IGNITION c fh (J1-2) $ (J1-1) Two SAFET seperote 18 See Grounding 3 ° 5-++0 +7 ots $ ‘ 30A 4 ‘ Y = (J1-25) NN en 9 6] a_ 7/0 o nN 8 9 "> —o |24 25 NOTE |23 10-0 12 SEE I » ; ri f 0-29 at +44-0 o-B0 )—_Y Ot ee 9 32 S Y rh a N. IV SN in S\ 4 \ IW 4 fh f\— “uo a a a a ?5 ©= at 2. 2 1 2 1 2 FAN 1 CONTROL RELAY SENSOR— ENGINE SPEED ; P 321 INJECTOR 1 INJECTOR 2 21 21 {==} {==} | 1 Temperature Motor Throttle Sensor Sensor 12 o |2 uy |3 &5 26 = GROUNDING NOTES ON S “I= (4A) 1n ) (7 5S I — rn BEATS a = 0 + I T > 4 = 5S ! ° TEMPERATURE 7? ° Vs. 1310 2olek LY fT SN\VS]\.

498 16,0 of ) 40 [27 ree S 5.— = 2% 0 126] | (J1-12) 11] 0 > S 0 |22 o GENERAL ° ry iS pat 5 | 0 ~e N.O. ~ | pp $ ot04720 ; o-~_ = mn GROUND NO. 1 A A) Battery Attached to engine block near starter. OR OUNDIN B) Lambda Sensor The sensor return is via the engine muffler. If a slip joint is used, a grounding strap is required. If a2 leaded sensor is used pin 4 or pin 21 can be used for the is the return. N OTE C) Fuel Pump Attached to the chassis D) Shield Attached to the engine block close to the coils.

B G = o BATTERY GROUND SEE GROUNDING NOTE A BATTERY GENERAL SYSTEM INSTALLATION NOTES The ignition switch must maintain a constant voltage to circuits 84, 85 and J1-2 as the key is swept from the start to the run position to prevent ECU reset during starting. The voltage on circuits 84,85 , J1-2 and J1-1 must remain within £0.2 V of each other regardless of system current draw to prevent differences between actuator voltages (circuits 65, 66,45, and 87) and system voltage (J1-1). If the ignition switch controls a powered circuit (i.e. lights, horn) it is recommended that a relay be used to control the power. To prevent signal errors, load circuits, (i.e.

horn, lights) shall not be powered from EFI engine or chassis wire harness A resistive spark plug with either a resistive spark plug wire or boot must be used to prevent electrical system noise. It is recommended that the ECU housing is mounted with the wire harness down to facilitate proper drainage away from the electrical connector. When not in operation, the battery must maintain a minimum system voltage of 7¥ with a current draw of 2 mA to maintain the adaptive memory. During starting, the system voltage must be 7V minimum for the ECU operation during cranking. Unless otherwise specified, all wires are 18AWG.

Speed sensor wires (pins 9 and 10) are to be a twisted pair with 1 twist/inch minimum. . Malfunction indicator lamp (MIL) can be a 12V// 0.25A incandescent lamp. Optionally, a 20 mA LED can be used. This requires a resistor of approximately 600 chms wired in parallel. 11. Normal operating voltage is to 16V dc -9Vdc, with a cold cranking voltage of 7V. 12. The throttle position sensor (TPS) connection shown is for CCW rotation of the TPS from idle to wide-open throttle as viewed from the throttle shaft side of the TPS. CW rotation requires switching the wires to TPS pins 1 and 3. soo A AWG Note - S