Brakes 42 4. Lift the edge of the brake plunger boot and check the plunger for existing lubrication. 2. From outside the cab, pull the valve away from the firewall; then remove the brake valve mount- ing adaptor and plunger. See Group 42 of the Heavy-Duty Trucks Service Manual for instruc- tions. If the plunger is dry, remove it by removing the brake pedal and brake plunger boot. Lubricate the plunger and inside surface of the boot with barium grease, part number BW 246671, or Pen- nzoil Adhezoplex EP 2; use only these approved lubricants. Install the plunger, boot, and brake pedal. 3.
Thoroughly clean any grease and contaminants from the brake valve mounting adaptor bore and the plunger surface. If the plunger has grease on it, lift the edge of the brake plunger boot enough to apply 2 to 4 drops of light oil around the brake plunger, where it slides into the brake base bracket. Reinstall the plunger boot around the brake base bracket. FLC 4. Inspect the adaptor bore and the plunger sliding surface for corrosion. The bore and plunger sur- faces should be smooth, with no pitting or rough- ness. Some discoloration is permissible. If there is pitting roughness, replace with new parts. See Table 3 . 5.
Apply one of the specified silicone greases to the sliding surfaces of the plunger and the adaptor bore. See Table 4 . If installing a new adaptor or plunger, first apply the grease included with the kit. 1. Clean any dirt, gravel, and other foreign material from the plunger boot and brake base bracket. 2. Check the brake plunger boot for cracks, holes, or deterioration. Replace if necessary. 6. Install the brake valve mounting adaptor and plunger, using a new gasket. 3. Lift the edge of the brake plunger boot and check the plunger for existing lubrication.
E-6 and E-12 Brake Valve Service Parts List If the plunger is dry, remove it by removing the cotter pin and clevis pin, and pulling the clevis pin out. Remove the piston rod and boot. Lift out the plunger. Lubricate the plunger and the tip of the piston rod with barium grease, part number BW 246671, or Pennzoil Adhezoplex EP 2; use only these approved lubricants. Install the piston rod, boot, clevis pin, and cotter pin. Description Part Number Qty.
Valve Adaptor BW 5002378 1 Plunger BW 5002379 1 Gasket 12—15695—000 1 Table 3, E-6 and E-12 Foot Brake Valve Service Parts List If the plunger has grease on it, lift the edge of the brake plunger boot enough to apply 2 to 4 drops of light oil around the brake plunger; do not over-oil. Install the plunger boot. Silicone Greases BW 291126 (silicone base grease spec.BW–650–M) 3.7 cc packet * Description Manufacturer Source 4. Lubricate the clevis pin with light oil. Allied Signal PDC 5. For E–12 valves, check for leakage; see Group 42 of the Heavy-Duty Trucks Service Manual for instructions.
FLD 55 O-RIng Lubricant (Formerly Molykote DC–55M Pneumatic Grease) Dow-Corning Corporation Locally NOTE: You may need to remove tie straps and an air line to gain access to the valve bore. It should not be necessary to remove the adaptor from the valve. V–755 O-Ring Lubricant Rhone-Poulenc Silicone VSI Inc. Locally * Each 3.7 cc packet is adequate to lubricate one foot valve adaptor as- sembly. Table 4, Silicone Greases 1. Remove the three mounting bolts that hold the foot brake valve on the firewall. Heavy-Duty Trucks Maintenance Manual, October 2009 42/12