volvo — page 54

Fuel system Note: A change of shim size by 0.1 mm (.0039 in) i mplies that the injection start is moved approx. 1 °. An increase in shim size reduces the injection angle and conversely a decrease in shim size in- creases the angle. Shims are available in the following sizes: 0.2, 0.3, 0.4 and 0.5 mm (.0078, .0118, .0157 and .0196 in). NOTE! In the event that no shims are required, li quid sealing compound should be used. Replace the pressure valve. Screw in the pressure valve holder by hand. If the pressure valve holder will not go in, screw the holder backwards and for- wards quickly 1/4-1/2 turn until the pressure valve goes in the pressure valve holder.

Screw down the pressure valve fully by hand until the 0-ring begins to be pressed together. Tighten after this with a 17 mm spanner. Tightening torque, see Technical data. Q WARNING! The pressure valve holder must be screwed in by hand so that it is possible to feel that the pressure valve goes correctly into the valve holder. Never use force to screw the valve holder down since this can damage the pressure valve. If the pressure valve cannot be turned in the valve holder the pump must be dismantled and the same method applied with the pump in a completely horizontal position. Fig. 91. Measurement of piston position with dial gauge 6.

Adjustment of the injection angle can also be made by measuring the piston height with a dial gauge. The table shows the crankshaft position in degrees when the piston is in a certain position in relation to B.T.D.C. Carry out the adjustment work as per items 4 and 5. The table shows the position of the piston In re- l ation to the crankshaft angle ('B.T.D.C.). 56 MD2O10, MD2020 MD2030 MD2040 Crankshaftangle 18°B.T.D.C. 19° B.T.D.C. 20° B.T.D.C. 21 'B.T.D.C. 22° B.T.D.C. 23° B.T.D.C. 24° B.T.D.C. 25°B.T.D.C. 26° B.T.D.C. 27° BT.D.C. Piston pos. - - - - - - 3.636 mm 3.937 mm 4.250 mm 4.573 mm Piston pos.

2.317 mm 2.577 mm 2.851 mm 3.138 mm 3.438 mm 3.750 mm 4.075 mm 4.413 mm 4.763 mm 5.125 mm Piston pos. 2.875 mm 3.199 mm 3.539 mm 3.895 mm 4.267 mm 4.655 mm 5.058 mm 5.477 mm 5.912 mm - MD2O10, MD 2020 MD2030 MD2040 Crankshaftangle 18° BT.D.C. 19 ° BT. D.C. 20° BT.D.C. 21° BT. D.C. 22° BT.D.C. 23° BT.D.C. 24° BT.D.C. 25° BT.D.C. 26° BT. D.C. 27° BT.D.C. Piston pos. - - - - - - . 1431 in. . 1550 in. . 1673 in. . 1800 in. Piston pos. .0912 in. 1014 in. . .1122 in. . 1235 in. 1353 in. . . 1476 in. . 1604 in. . 1737 in. 1875 in. . .2017 in. Piston pos. .1131 in. .1259 in. .1393 in. .1533 in. . 1679 in. .1832 in. . 1991 in. .2156 in. .2327 in. -