Yanmar — 3.2 Quick reference chart for troubleshooting

3. Troubleshooting (IV) Faulty fuel injection valve (1) Faulty valve seat (2) Sticking of valve needle (3) Worn valve needle (4) Clogged outlet (5) Low injection pressure (1) Incorrect thickness of gasket packing (2) Faulty installation of governor ring and lever (5) Clogging of suction/exhaust pipes (4) Faulty engine starter (3) Governor handle is in stop position (VII-1) Replace. (VII-2) Adjust . (VII-3) Move governor handle to acceleration position. (VII-4) Check and repair. (VII-5) Clean. Chart 7 STARTING TROUBLE TROUBLE WITH STARTING (IV-1) Lap. (IV-2) Lap. (IV-3) Replace. (IV-4) Clean or replace. (IV-5) Adjust.

(VIII) Miscellaneous (8) Water in fuel oil tank (7) Damaged fuel oil supply pump (1) Air leakage from suction/exhaust valves (2) No tappet clearance (3) Faulty gasket packing (4) Upper part of cylinder liner worn (1) Imperfect priming of fuel oil system (2) Injection cut off due to faulty governor (4) Insufficient fuel oil in tank (3) Clogging of fuel inlet filter (5) Fuel oil tank cock closed (6) Clogging in fuel oil pipe (7) Insufficient tightening of head bolts (8) Damaged valve spring (III-1) Prime well. (III-2) Adjust. (III-3) Clean out matter causing clogging. (III-4) Add fuel to fuel tank. (III-5) Open cock. (III-6) Clean. (III-7) Disassemble and repair or replace.

(III-8) Drain water from fuel system and prime. (5) Worn piston ring (6) Piston ring sticks (VII) Leakage of pressurized air (III) Fuel oil not injected (VII-1) Lap valves. (VII-2) Adjust . (VII-3) (VII-4) (VII-5) Replace. (VII-6) Disassemble and repair or replace. (VII-7) Tighten tightening nuts uniformly. (VII-8) Replace. (8) Excessive resistance between battery and starter (9) Insufficient battery charge (7) Slippage of starter clutch (2) Loose high pressure fuel pipe (3) Damaged high pressure fuel pipe (5) Cut starter coil (6) Worn commutator (1) Fuel injection pump timing irregular (4) Air in high pressure fuel pipe (II-1) Tighten. (II-2) Repair using sandpaper. (II-3) Replace.

(II-4) Repair using sandpaper (Type 500 600). (II-5) Replace. (II-6) Undercut and repair or replace. (II-7) Replace. (II-8) Replace with thicker or shorter wire. (II-9) Charge. (VI) Faulty fuel injection system (II) Ring gears do not mesh (VI-1) Adjust. (VI-2) Tighten firmly. (VI-3) Replace. (VI-4) Bleed air. (2) Faulty connection in engage magnet switch (3) Worn brushes (4) Commutator rough and dirty (1) Loose battery starter terminal (V-2) Replace. (V-5) Bleed air. (V-6) Replace. (I-1) Tighten. (I-2) Repair using sandpaper or replace. (I-3) Replace. (I-4) Repair using sandpaper and then grease. (I-5) Adjust. (I-6) Adjust. (I-7) Replace.

(5) Edges of gear teeth misshapen (I) Pinion gears do not mesh TROUBLE AND TROUBLESHOOTING (1) Loose battery engage magnet terminal (2) Faulty connection in starting switch magnet coil (2) Damaged plunger spring Countermeasure Cause and Effect Countermeasure 56 Chart 7 TROUBLE AND TROUBLESHOOTING TROUBLE WITH STARTING Chart 7 TROUBLE AND TROUBLESHOOTING TROUBLE WITH STARTING Countermeasure (I-1) Tighten. (I-2) Repair using sandpaper or replace. (I-3) Replace. (I-4) Repair using sandpaper and then grease. (I-5) Adjust. (I-6) Adjust. (I-7) Replace. (II-1) Tighten. (II-2) Repair using sandpaper. (II-3) Replace. (II-4) Repair using sandpaper (Type 500 600). (II-5) Replace.

(II-6) Undercut and repair or replace. (II-7) Replace. (II-8) Replace with thicker or shorter wire. (II-9) Charge. (III-1) Prime well. (III-2) Adjust. (III-3) Clean out matter causing clogging. (III-4) Add fuel to fuel tank. (III-5) Open cock. (III-6) Clean. (III-7) Disassemble and repair or replace. (III-8) Drain water from fuel system and prime. (IV-1) Lap. (IV-2) Lap. (IV-3) Replace. (IV-4) Clean or replace. (IV-5) Adjust.