2. Programming Concepts 2-33 OFF STOP RUN Special ES2 SA2 Latch Content SS2 SX2 Attrib. Default D EX2 SE -ed ON RUN STOP D1057* High word of X0’s input pulse frequency (Unit: 0.001Hz) It is used with M1357. V3.22 ╳ ╳ V2.66 0 0 - R NO 0 D1058* Low word of X1’s input pulse frequency (Unit: 0.001Hz) It is used with M1358. V3.22 ╳ ╳ V2.66 0 0 - R NO 0 D1059* High word of X1’s input pulse frequency (Unit: 0.001Hz) It is used with M1358. V3.22 ╳ ╳ V2.66 0 0 - R NO 0 D1062* Average number of times an analog signal is input to the EX2/SX2 series PLC The default value is K10 for EX2 version 2.6 and version 2.8.
○ ╳ ╳ ○ 2 - - R/W YES 2 D1067* Error code for program execution error ○ ○ ○ ○ 0 0 - R NO 0 D1068* Address of program execution error ○ ○ ○ ○ 0 - - R NO 0 D1070 ↓ D1085 Feedback data (ASCII) of Modbus communication. When PLC’s RS-485 communication instruction receives feedback signals, the data will be saved in the registers D1070~D1085. Usres can check the received data in these registers. ○ ○ ○ ○ 0 - - R NO 0 D1086 High word of the password in DVP-PCC01 (displayed in hex according to its ASCII codes) ○ ○ ○ ○ 0 - - R/W NO 0 D1087 Low word of the password in DVP-PCC01 (displayed in hex according to its ASCII codes) ○ ○ ○ ○ 0 - - R/W NO 0 D1089 ↓ D1099 Sent data of Modbus communication.
When PLC’s RS-485 communication instruction sends out data, the data will be stored in D1089~D1099. Users can check the sent data in these registers. ○ ○ ○ ○ 0 - - R NO 0 D1109* COM3 (RS-485) Communication protocol ○ ╳ ○ ○ H’86 - - R/W NO H’86 D1110* Average value of EX2/SX2 analog input channel 0 (AD 0) When average times in D1062 is set to 1, D1110 indicates present value.
○ ╳ ╳ ○ 0 - - R NO 0 D1111* Average value of EX2/SX2 analog input channel 1 (AD 1) When average times in D1062 is set to 1, D1111 indicates present value ○ ╳ ╳ ○ 0 - - R NO 0 D1112* Average value of EX2/SX2 analog input channel 2 (AD 2) Whenaverage times in D1062 is set to 1, D1112 indicates present value ○ ╳ ╳ ○ 0 - - R NO 0 D1113* Average value of 20EX2/SX2 analog input channel 3 (AD 3) Whenaverage times in D1062 is set to 1, D1113 indicates present value ○ ╳ ╳ ○ 0 - - R NO 0 Displaying the status of the analog input channel of 30EX2 ○ ╳ ╳ ╳ 0 - - R NO 0 D1114* Enable/disable 20EX2/SX2 AD channels (0: enable (default) / 1: disable) bit0~bit3 sets AD0~AD3. P.S.
30EX2 does not support this function. ○ ╳ ╳ ○ 0 - - R/W YES 0 D1115* 20EX2/SX2 analog input/output mode setting ○ ╳ ╳ ○ 0 0 0 R/W YES 0 30EX2 analog input/output mode setting ○ ╳ ╳ ╳ - - - R/W YES H’FFFF D1116* Output value of analog output channel 0 (DA 0) of EX2/SX2 ○ ╳ ╳ ○ 0 0 0 R/W NO 0 D1117* Output value of analog output channel 1 (DA 0) of 20EX2/SX2 P.S. 30EX2 does not support this function. ○ ╳ ╳ ○ 0 0 0 R/W NO 0 D1118* EX2/SX2 sampling time of analog/digital converstion. Default: 2. Unit: 1ms. Sampling time will be regarded as 2ms if D1118≦2 ○ ╳ ╳ ○ 2 - - R/W YES 2