DVP-ES2/EX2/SS2/SA2/SX2/SE&TP Operation Manual - Programming 2-34 OFF STOP RUN Special ES2 SA2 Latch Content SS2 SX2 Attrib.
Default D EX2 SE -ed ON RUN STOP D1120* COM2 (RS-485) communication protocol ○ ○ ○ ○ H’86 - - R/W NO H’86 D1121* COM1(RS-232) and COM2(RS-485) PLC communication address ○ ○ ○ ○ - - - R/W Yes 1 D1122 COM2(RS-485) Residual number of words of transmitting data ○ ○ ○ ○ 0 0 - R NO 0 D1123 COM2(RS-485) Residual number of words of the receiving data ○ ○ ○ ○ 0 0 - R NO 0 D1124 COM2(RS-485) Definition of start character (STX) ○ ○ ○ ○ H’3A - - R/W NO H’3A D1125 COM2(RS-485) Definition of first ending character (ETX1) ○ ○ ○ ○ H’0D - - R/W NO H’0D D1126 COM2(RS-485) Definition of second ending character (ETX2) ○ ○ ○ ○ H’0A - - R/W NO H’0A D1127 Number of pulses for ramp-up operation of positioning instruction (Low word) ○ ○ ○ ○ 0 - - R/W NO 0 D1128 Number of pulses for ramp-up operation of positioning instruction (High word) ○ ○ ○ ○ D1129 COM2 (RS-485) Communication time-out setting (ms) ○ ○ ○ ○ 0 - - R/W NO 0 D1130 COM2 (RS-485) Error code returning from Modbus ○ ○ ○ ○ 0 - - R NO 0 D1131 Input/output percentage value of CH0(Y0,Y1) close loop control ○ ○ ○ ○ 100 - - R/W NO 100 D1132 Input/output percentage value of CH1(Y2,Y3) close loop control ○ ○ ○ ○ 100 - - R/W NO 100 D1133 Number of pulses for ramp-down operation of positioning instruction (Low word) ○ ○ ○ ○ 0 - - R NO 0 D1134 Number of pulses for ramp-down operation of positioning instruction (High word) ○ ○ ○ ○ 0 - - R NO 0 D1135* Pulse number for masking Y2 when M1158 = ON (Low word) ○ ○ ○ ○ 0 0 - R/W NO 0 D1136* Pulse number for masking Y2 when M1158 = ON (High word) ○ ○ ○ ○ 0 0 - R/W NO 0 D1137* Address where incorrect use of operand occurs ○ ○ ○ ○ 0 0 - R NO 0 D1140* Number of I/O modules (max.
8) ○ ○ ○ ○ 0 - - R NO 0 D1142* Number of input points (X) on DIO modules ○ ○ ○ ○ 0 - - R NO 0 D1143* Number of output points (Y) on DIO modules ○ ○ ○ ○ 0 - - R NO 0 D1145* Number of the connected let-side modules ╳ ╳ ○ ○ 0 - - R NO 0 D1150* Vale fetched from the hardware counter C243/C245/C246/C247/C248/C251/C252 (Low word) V 3.28 V 3.28 SA2: V2.82 V2.82 0 - - R/W NO 0 D1151* Value fetched from the hardware counter C243/C245/C246/C247/C248/C251/C252 (High word) V 3.28 V 3.28 SA2: V2.82 V2.82 0 - - R/W NO 0 D1152* Value fetched from the hardware counter C244/C249/C250/C253/C254 (Low word) V 3.28 V 3.28 SA2:
V2.82 V2.82 0 - - R/W NO 0 D1153* Value fetched from the hardware conter C244/C249/C250/C253/C254 (High word) V 3.28 V 3.28 SA2: V2.82 V2.82 0 - - R/W NO 0 D1167 The specific end word to be detected for RS instruction to execute an interruption request (I140) on COM1 (RS-232).
○ ○ ○ ○ 0 - - R/W NO 0 D1168 The specific end word to be detected for RS instruction to execute an interruption request (I150) on COM2 (RS-485) ○ ○ ○ ○ 0 - - R/W NO 0 D1169 The specific end word to be detected for RS instruction to execute an interruption request (I160) on COM3 (RS-485) ○ ╳ ○ ╳ 0 - - R/W NO 0 D1175 Number of communication packets received via broadcasting (number of slaves) by executing CANRS instruction ES2-C ╳ ○ ○ 0 0 - R NO 0 D1176 Error code for ETHRS instruction (available for ES2-E: V1.2, 12SE: V1.92, 26SE: V2.00 and later) ES2-C ╳ SE ╳ 0 0 - R NO 0 D1177 Communication timeout setting for CANRS instruction (available for ES2-C: V3.48, SA2/SX2: V2.89, SE:
V1.83 and later) ES2-C ╳ ○ ○ 200 - - R/W NO 200 D1178 VR0 value ╳ ╳ ○ ○ 0 - - R NO 0