Base - July 2006 Revi - June 2007 Print 603.93.431 3-44 FITTING SUPER STRUCTURES EUROCARGO EURO 4 - 5 Table 3.12 — Cranes mounted behind cab (subframe fixing with shear-resistant plates) 2) Model A x B x t (mm) (N/mm 0,2 subframe 0/20 20/30 30/40 40/50 50/60 60/70 70/80 80/90 90/100 100/120 120/140 140/160 160/180 180/200 200/220 220/240 240/260 260/280 280/300 R Minimum value of strength modulus of subframe section Wx (cm3) ML60, ML65, ML75, ML80EL 172, 5x65x4 240 A A 31 46 57 89 105 E 360 A A A 31 46 57 89 105 119 E ML60, ML65, ML75, 172, 5x65x5 240 A A A 31 46 89 89 119 E ML80EL 360 A A A A 31 46 57 57 89 E ML80, ML90, ML100 195, 5x65x4 240 A A A 31 46 89 89 105 E 360 A A A A 31 46 57 89 105 E ML80, ML90, ML100 195, 5x65x5 240 A A A 31 46 57 89 89 119 E ML110EL *), ML120EL *) 360 A A A A A 31 46 57 89 105 E ML110EL *), ML120EL *) 195, 5x65x6 240 A A A 31 46 57 89 119 135 E 360 A A A A 19 36 46 57 89 E ML120, ML140, 240x70x5 240 A A A A A 21 36 57 89 105 E ML150E, MLI60E, ML100EW 360 A A A A A A A 21 36 89 105 E ML120, ML140, ML150, MLI60E, ML140EW 240x70x6 240 A A A A A A 31 46 89 89 E 360 A A A A A A A A 31 57 89 E ML120, ML140, 240x70x6, 7 240 A A A A A A 21 36 57 89 E ML150, MLI60E 360 A A A A A A A A 21 46 89 105 E ML150E, MLI60E 240x70x7, 7 240 A A A A A A A 31 46 57 105 173 208 E 360 A A A A A A A A 21 36 46 89 119 135 E ML180E, ML190EL 262, 5x80x6 240 A A A A A A 21 21 36 89 105 150 208 245 E 360 A A A A A A A A 21 31 57 89 105 135 173 208 245 E ML180E, MLI90EL 262, 5x80x6, 7 240 A A A A A A A A 36 89 105 135 173 208 E 360 A A A A A A A A A 21 46 89 89 135 150 173 208 245 E ML180E MLI90EL 262, 5x80x7, 7 240 A A A A A A A A 21 57 89 135 150 208 245 E 360 A A A A A A A A A 21 36 89 89 135 150 173 208 245 E A = The reinforcing profile prescribed for the respective superstructure is sufficient (e.g.
for normal bodies). Close the reinforcing profile in the crane mounting area. In the crane area, reinforcing profiles with thickness of less than 5 mm must be reinforced. E = To be checked on a case-by-case basis. Send the technical documentation with the checks of stresses and stabilityto theappropriate IVECObodies. *) = On the version with sleeper cab, use a profile with strength modulus Wx of not less than 57 cm3.
If the height of the subframe profile has to be reduced, using shear resistant connections between chassis and subframe, combined section profiles can be used, as shown in Figure 3.30, instead of the C-profile, provided that the flange width and thickness are not less than the corresponding values of the profile recommended by IVECO. The above are general conditionswhich apply to the materialsindicated. To assess whetherit ispossible to use materials with higher mechanical specifications, it is necessary to check the total resistant moment of the chassis plus subframe.
Since reducing the height of the subframe profile also reduces the torsion resistance, forcraneswith four stabilisers, the bodybuildermust take special measuresto ensure adequate torsional rigidity of the subframe in the crane mounting area. For this reason, it is recommended that you do not use profiles with a height of less than 120 mm. Since the execution of these solutions also limits the torsional capacity of the chassis, they can only be used on vehicles intended exclusively for on-road use.