Department of Defense MIL-HDBK-816 Notice 1 — MIL-HDBK-816 Notice 1 Radiation Hardness Assurance Guidelines Manual PDF

Downloaded from https://www.everyspec.com MIL-HDBK-816 NOTICE 1 devices, produced by ionizing radiation, or (c) latch-up or burnout produced by photocurrents or by single ionized tracks. Trapped charge effects are sometimes called ionizing radiation dose effects or total dose effects. However, because of time dependent effects after irradiation, specifying the total dose is not considered adequate for describing these effects. 4.1.2 Radiation hardness assurance. If nondestructive electrical measurements alone could be used to predict the performance of a part type in a radiation environment, then the hardness assurance problem would be largely solved.

One of the cases where such measurements have proven useful has been that of using transistor current gain-bandwidth product, f t , measurements to screen out (by requiring f t to be above some minimum value) parts which would be extra sensitive to neutron displacement damage. For ionizing radiation dose, it is necessary to use actual radiation tests to assure the radiation response of a part. In practice, radiation hardness assurance is achieved most commonly through the use of LAT which are performed on the lots that are being purchased. 4.1.3 Dose rate tests. For the dose rate upsets discussed previously, if sufficient care is used, radiation tests can be non-damaging.

Thus, parts which have been tested can be used for production. In this case 100 percent of the parts to be used for system production can be tested (screened) and a high degree of assurance can be obtained that the parts will meet system requirements. Caution is still required, because there exists some possibility, especially for complex microcircuits, that the screening tests conducted will not have covered the worst case conditions or exercised all possible paths. MIL-HDBK-815, entitled: “Dose-Rate Hardness Assurance Guidelines”, may be consulted for a detailed discussion of this problem. 4.1.4 Displacement damage, steady state ionization and single event upsets.

For displacement damage, steady state ionization effects, and single event upsets, the radiation tests are damaging and it is generally not possible to use the tested parts in the system. The use of damaging radiation tests thus produces the central problem of hardness assurance, namely, that estimates of the survival probability of the parts to be used in the system must be based on statistical inference from a tested sample of parts which are degraded by the tests and therefore cannot be used in the system. This problem is compounded by the fact that production processes can vary so that the currently produced radiation hard parts may not be typical of those that were measured in the past.

This case, which is common, has been carefully reviewed by both users and manufacturers of semiconductor devices. The consensus opinion is that, if no additional information is available, the degree of hardness assurance obtained from the detailed specification is limited statistically to that provided by the radiation LAT or Quality Conformance Inspection (QCI) that are performed (the term QCI is reserved for tests performed by the manufacturer before the lot is approved for shipment). 4.2 Military Standard procurement system.

In order to make high reliability hardness assured devices available to designers and manufacturers of systems, the existing military standard procurement system was augmented a few years ago to include RHA semiconductor devices. At the present time, QML RHA parts are labeled by letter designators which indicate that the part type has passed lot acceptance tests based on a sample of parts tested at the radiation levels shown in table I. 4.3 Lot acceptance tests. Lot acceptance tests are used in the military standard system for determining whether a production lot is of high enough quality so that it can be shipped by the vendor.

The tests are of a statistical nature and fall into two general categories: (a) attribute tests and (b) variables tests. 4.3.1 Attribute variables tests. Attribute tests are the tests most often used in the military standard procurement system. For this reason, these guidelines will be directed at the use attribute tests for lot acceptance. Variables tests, on the other hand, are often used for qualifying and accepting system production parts and, for such use, may depend on the particular hardness assurance and derating procedures that the given system is using.

Variables tests, therefore, more properly should be discussed as part of a system hardness assurance guideline document and, for that reason, are not discussed in detail here. SUPERSEDES PAGE 9 OF MIL-HDBK-816 9