Atari Games Final Lap — final_lap_2.jpg

Final Lap Maintenance meshes with and is the same height as the gear on 11. Reconnect the wiring assembly. 18. Be sure the gear set screw is on the flat part of the potentiometer shaft and at twelve o’clock. Tighten the set screw. 19. Tighten the lock nut on the potentiometer. 20. Replace the screw in the spring bar. Tighten the screw. 21. Replace the pedal. Tighten the four screws that hold the pedal assembly onto the front plate. Replace the foot pedal plate and tighten the two screws that hold it in place. 22. Reconnect the wiring assembly. The wires to the brake (the left pedal) potentiometer are red on the top, orange in the middle and black on the bottom.

The wires to the gas (the right pedal) potentio- top, orange in the middle and black on the bottom. The wires to the gas (the right pedal) potentiometer are red on the top, yellow in the middle, and black on the bottom. 12. Replace the pedal assembly in the game. Removing the Video Display Perform the following procedure to remove the video display. (See Figure 3-4.) 1. Turn the game power off and wait two minutes. Unplug the power cord. WARNING meter are red on the top, yellow in the middle, and black on the bottom. Replacing the Pedal Voltage all precautions necessary Potentiometers If the gas or brake pedal fails the self-test, you may need to replace the potentiometer.

However, first make sure that the mechanical parts of the pedal are functioning properly. Take the pedal assembly out of the game. Use a 5/32-inch Allen head wrench to remove the four screws on the cover plate. Pull the assembly out to- wards the seat. 2. High The video display contains lethal high voltages. To avoid injury, do not attempt to service this display until you observe 23. Install the pedal assembly in the game. 1, The wires to the brake (the left pedal) potentiometer are red on the the pedal. Remove the wiring harness from the gas and brake for working on high-voltage equipment. X-Radiation The video display has been designed to minimize X-radiation.

However, to avoid possible exposure to soft X-radiation, never modify the high-voltage circuitry. Implosion Hazard The cathode-ray tube may implode if struck or dropped. Shattered glass may cause injury within a 6-foot radius. Use care when handling the display. potentiometers. 3. Loosen the lock nut on the potentiometer with a 1/2-inch flat wrench. 2. Remove 4. Loosen the set screw on the gear on the potentiometer. 5. Take off the nut, washer, and gear and remove the potentiometer. 3. Be sure that the game power is turned off before discharging the high voltage from the cathode-ray tube (CRT). The display assembly contains a circuit for discharging the high voltage to ground when 6.

Put on the new the curved middle service panel and then the top service panel. certain, al- al assembly case. a. Attach one end of a large, well-insulated, 18- 7. Put on the washer and lock nut. Tighten the lock nut part way. b. Momentarily touch the free end of the grounded 8. Replace the gear on the shaft. Make sure it completely meshes with and is the same height as the pedal gear. Be sure the gear set screw is on the flat part of the potentiometer shaft and at twelve o’clock. Tighten the set screw. potentiometer. Make sure you in- - sert the potentiometer key into the hole in the ped- 9. 10. Tighten the lock nut on the potentiometer. 3-8 power is removed.

However, to make ways discharge the display as follows: gauge jumper wire to ground. jumper to the CRT anode by sliding it under the anode cap. c. Wait two minutes and repeat part b. 4. Disconnect the display harness connectors from the display. 5. Use a 3/8-inch nut driver to remove the four hex head screws holding the video display mounting