U.S. Army Material Command (AMC) AMCP 706-210 — FUZES - Engineering Design Handbook AMCP 706-210 (U.S. Army) PDF Download

Ј AMCP 70210 Downloaded from https://www.everyspec.com these necestate relative movement between a dance falls which again tends to hold the voltage magnet and a conducting coil. applied to the load constant. The generated voltape depends upon the num- The other form of electromagnetic generator bet of lines of magnetic force which the conduc- can be used in contact-sensing fuzes. Upon im- tor can cut and the velocity with which this cut- pact, a magnet is pushed through a coil or a ting is accomplished. As an example of the first coil is pushed past a magnet.

This can be done type, a fuze may be supplied with energy from either by using the impact forces directly to an electric generator that is wind-driven by an move one or the other members, or by using the external propeller at speeds up to 50,000 rpm. impact forces to release the moving element The generator must be small, light, rugged, which would then be spring-driven past the other stable, and simple in operation. The rotor is a elements. small permanent magnet while the stator carries Induced voltage for this second type of elec- two windings, one for low voltage and the other tromagnetic generator follows the same law as for high voltage. The low voltage, AC, heat.

the that stated for the rotated generator. The flux vacuum tube filaments but the high voltage is can be changed by altering the gap size in the rectified with a selenium rectifier and the re- magnetic circuit, by removing or adding a keeper sulting DC siaa is filtered for the plate supply. to the magnet, or by introducing other materials This voltage may also be used to fire an electric into the magnetic circuit. Any of these circuit detonator, changes can be accomplished with the mechani- Fig. 3-7 shows a typical circuit for an elec- cal forces available during impacts.

trical system tha& can be solved for the voltage across the load resistance RL by applying Max- 3-4.3.3 BatWti well's loop current methods. Here Batteries are appealing because they can be adapted to a large number of situations. They E - d (3-1) aof several types'. II Batteries with radioactive elements are, in gen- eral, high-voltage low-current-drain cells. These where E is the generated voltage, N is the num- are usually used to keep a capacitor charged. ber of turns in the coil, and d4b/dt is the rate of They have good temperature and age characteris- change of the flux in weber/sec. The flux is rela- tics.

Wet-cell type batteries can be designed with tively constant, but since the rotor speed varies any output from low-voltage, low-drain batteries widely, E also varies. The voltage may be regu- to high-voltage, high-drain batteries. At present lated by the following method: The load resist- most of them have poor age and temperature ance is made small in comparison with the in- characteristics. In solid electrolyte batteries, a ductive reactance of the stator winding. Then as solid replaces the liquid electrolyte of the wet the rotor speed increases, the frequency of the cell. Such batteries are restricted to small cur- generated voltage increases.

However, the in- rents because of their high internal resistance. ternal impedance of the generator increases Reserve batteries are those that are activated just which tends to hold the output voltage constant. prior to launching (by some external force) or Also a capacitor is shunted across the load re- during launching (by using the launching forces). sistor. As the frequency increases, the impe- They can be designed for a wide range of con- ditions and have good age and temperature INDUCTIVE REACTANCE xL characteristics. One of the most common fuze batteries in GENERATED LO EACTANCE j .^ sTvt battery is basically a primary voltaic cell of the V0LTG RRE xNT LOO Lo reserve type 4 .

During storage, the electrolyte is Eg CURRENT CRET RL APACTIVEI use today is the thermal battery. A thermal g in an inactive solid state. When heat is applied to the electrolyte (temperature of about 7500F), the electrolyte becomes a liquid ionic conductor. Figure 3.7. Typical Circuit for Wind-driven I A complete thermal battery contains an integral Generator source of heat that is inert until required for 3-8