U.S. Army Material Command (AMC) AMCP 706-210 — FUZES - Engineering Design Handbook AMCP 706-210 (U.S. Army) PDF Download

Downloaded from https://www.everyspec.com AMCP 706-210 chap is initiated by one or several leads or by a the shape is commonly dictated by space con- detonator; it amplifies the detonation wave to a siderations. If the booster charge is external to sufficient magnitude or maintains detonating the bunting charge, extreme ratios of length to conditions for a long enough time to initiate the diameter are to be avoided. For best output, the main charge of the munition. length to diameter ratio should be greater than In common usage, the term booster charge is 0.3 and less than 3.0. Ratios in the order of 2" 3 abbreviated to booster. Actually, a booster is a or 1:2 seein to be optimni.

Shapes with an in- separate fuze component provided to augment creasing cross section outward from the initiating the other explosive components of a fuze so as end are more efficient, but difficult to load to cause detonation of the main explosive filling, uniformly' 3 . It consists of a housing, the booster charge, a detonator, and an auxiliary arming device. A booster is shown in Fig. 10-6 wherein part O is 44.5 SPECIAL EXPLOSIVE ELEMENTS the booster charge. A number of special explosive components may be found in explosive trains or as inde- 4-4.4.1 Explosives Used in Booster Charis pendent elerrentA.

The density to which the explosive is packed 'hito a booster charge affects both sensitivity and 4-4.5.1 Actuators output. Thus loading techniques are important. At present, there are three methods for loading An actuator is an explosive-actuated mechani- booster cups: (1) loading a preformed, fully con- cal device which does not have an explosive out- solidated pOet, (2) inserting a ppeformed pellet put. In an explosive train, it is used to do me- and applying consolidating pressure with the chanical work such as close a switch or align a pellet in place, and (3) pouring a loose charge rotor. Most present actuators are electrically ini- into the cur and consolidating it in place. tiated.

They are discussed more fully in par. 7-2. The first method is the most convenient in production and the most widely used in fuze 44.5.2 Igniters (Squibs) practice. Pellets can be produced to close size tolerances and uniformity. However, this method Igniters or squibs are used to ignite propel- is not acceptable with more complicated shapes lants, pyrotechnics, and flame-sensitive explo- or in some high performance weapons. Conical sives. They have a small explosive output that shapes, for example, are always pressed in place. consists of a flash or a flame' 4 . A typical squib Each of the last two methods assures a firmer is shown in Fig. 4-6.

Igniters are electrically ini- mounting of the explosive by positively pre- tiated and are similar in construction to electric venting voids between pellet and cup. Hence, primers, Igniters consist of a cylindrical cup (usu- one or .he other must be used when the round ally aluminum, copper, or plastic), lead wires, a is subjected to accelerations sufficiently large to plug and a wire or carbon bridge assembly, and a shift, fracture, or further consolidate the pellet small explosive charge. The cup may be vented since these conditions may lead to premature or or completely open on the output end. improper detonations.

The third method is the most convenient when only a few samples are 4-4.5.3 F needed. Tetryl and RDX are the most widely used ex- plosives for boosters. Other explosives have been tain a column of black powder or pyrotechnic used, such as granular TNT, RDX and material. (Note the spelling of fuses as distin. tures, and PETN. guished from fu2es.) They ale used to transmit fire to a detonator but only after a specified 4-4.4.2 Description of Booster Charges time delay. Delay times are adjusted by varying the length of the fuse.

Delay fuses were em- While the shape of th3 explosive charge affects ployed in early designs of hand grenade and input and output characteristics to some extent, pyrotechnic explosive trains. 4-11 L