Email: sales@impulseautomation.co.uk Website: www.impulseautomation.co.uk RM040 Series Linear Solenoid Push and/or Pull Type Heavy duty linear solenoid RM 040 Weight: Complete solenoid: appr. 380 g Armature: appr. 60 g Standard: Voltage: 24 V DC Flying leads: 10 cm Insulation class: F (max. permissible temperature = 155 ° C) Service-free DU armature bearing for maximum durability. RM040 24VDC100 %ED 2) If solenoid is mounted directly onto a flat metal surface, an increase in relative duty cycle is permissible (please ask for advice) Document LNSRM4/15 Revision 00 2 100 %ED F [N] 50 5 20 15 Force vs.

Stroke diagram F = f (s) 10 25 5 40 Force measured when operating in horizontal position, at 90 % rated voltage and with winding at operating temperature 100 2 stroke s = 0 corresponds to armature in fully home position 1 0 1 2 3 4 5 6 7 8 9 10 S [mm] Impulse Automation Limited United Kingdom Company Registration 665193 Information shown in these data sheets are for guidance purposes only, no liability is accepted for any errors or omissions. The designer or user is solely responsible for the safe and proper use of these parts, assemblies or equipment described. 100 40 25 15 5 % Perm. duty cycle (ED)2) 11 21 41 67 161 W Nominal coil power Pn 36 11 ms Actuation time (ED)

Page 1

Email: sales@impulseautomation.co.uk Website: www.impulseautomation.co.uk RM040 Series Linear Solenoid Push and/or Pull Type M5 Ш 26 31,7 16 +1 16 +1 4 4 17 5 ± 0,2 5 ± 0,2 45 16 7 45 39 128 Direction of stroke Direction of stroke M5 Ш 26 Ш22 Dimensions given with armature in fully home position M3 Ш 22 Ш 30 Ш 40 30 Ш 3,5 19 M3 Ш 30 Dimensions given with armature in fully home position M 5 Ш26 Document LNSRM4/25 Revision 00 2 31,7 16 +1 16 +1 4 17 7 17 5 ± 0,2 5 ± 0,2 58 29 58 65 7 28 M 5 Ш 26 Ш 22 Impulse Automation Limited United Kingdom Company Registration 665193 Information shown in these data sheets are for guidance purposes only, no liability is accepted for any errors or omissions.

The designer or user is solely responsible for the safe and proper use of these parts, assemblies or equipment described. without stroke limiter 52 ≈17 34 0 3 with stroke limiter

Page 2

Email: sales@impulseautomation.co.uk Website: www.impulseautomation.co.uk RM040 Series Ordering Information 2) See below 3) Opposite to electrical connection 4) Same side as electrical connection 6) For plug-in socket 6.3 DIN 46247 and plug 200 +15 Z801 and Z811 Coil terminals N F Examples of design types: Direction of stroke Document LNSRM4/35 Revision 00 2 Impulse Automation Limited United Kingdom Company Registration 665193 Information shown in these data sheets are for guidance purposes only, no liability is accepted for any errors or omissions. The designer or user is solely responsible for the safe and proper use of these parts, assemblies or equipment described.

RM 040 – W – O R O R – N – 24 V DC 100 % ED Ord er specifications RM Line ar solenoid series 040 Des ign type ø mm W Hor izontal frontal force vs. stroke output Des cription2) O Stroke limit without H with R Plunger right hand side3) B both sides O Flange without R right hand side3) L left hand side4) O Gaiter without R right hand side3) L left hand side4) B both sides F Coi l terminals Flying leads (10 cm standard length) N plug-in socket connection6) 24 Op erating voltage 24 V DC 205 205 V DC (connected to 230 V AC with SI- bridge rectifier) 100 % ED Per m. duty cycle under air cooled conditions (LK) ca.12 ca.12

Page 3

Email: sales@impulseautomation.co.uk Website: www.impulseautomation.co.uk RM040 Series Accessories 41,0 10,0 Plug-in socket Z801 Screw joint PG 9 for lead diameter 4.5 - 7 mm 5,5 34,2 Plug-in socket Z811 Screw joint PG 11 for lead diameter 6 - 9 mm Plug-in socket with built in Si-bridge rectifier (30,5) Flange (Mounting screws are part of the shipment) ШJ ШG ШЕ ШF ШD Order specification C B H Document LNSRM4/45 Revision 00 2 Impulse Automation Limited United Kingdom Company Registration 665193 Information shown in these data sheets are for guidance purposes only, no liability is accepted for any errors or omissions.

The designer or user is solely responsible for the safe and proper use of these parts, assemblies or equipment described. Ø 19,0 ØI ØL K A ØI ØL K A ØL K Order Dimensio ns (mm) Dimensi ons (mm) Order number Type A B C D E F G H I J K L Type number Z 837 RM 040 40,0 7,0 12,0 22,0 18,6 22,0 – – 3 ,5 3,4 33,0 30,0 RM 040 Z 837

Page 4