Kuhnke RM100 Linear Solenoid Datasheet (EN)

Email: sales@impulseautomation.co.uk Website: www.impulseautomation.co.uk RM100 Series Linear Solenoid Push and/or Pull Type Heavy duty linear solenoid RM 100 Weight: Complete solenoid: appr. 6400 g Armature: appr. 1100 g Standard: Voltage: 24 V DC Flying leads: 20 cm Insulation class: F (max. permissible temperature = 155 ° C) Service-free DU armature bearing for maximum durability. Stroke of version with standard stroke limiter: 30 mm. 1) If solenoid is mounted directly onto a flat metal surface the duty cycle can be extended (please ask for advice) 2000 %ED Document LNSRM1/15 Revision 00 2 700 1000 500 Force vs.

Stroke diagram F = f (s) 200 25 15 5 100 40 W = horizontal characteristic 50 100 Force measured when operating in horizontal position, at 90 % rated voltage and winding at operating temperature F/N 10 20 stroke s = 0 corresponds to armature in fully home position 0 10 20 30 40 s/mm Impulse Automation Limited United Kingdom Company Registration 665193 Information shown in these data sheets are for guidance purposes only, no liability is accepted for any errors or omissions. The designer or user is solely responsible for the safe and proper use of these parts, assemblies or equipment described. 100 40 25 15 5 % Perm.

duty Cycle (ED)1) 69 162 255 400 1071 W Nominal coil power Pn 110 45 ms Actuation time (ED)

Стр. 1

Email: sales@impulseautomation.co.uk Website: www.impulseautomation.co.uk RM100 Series Linear Solenoid Push and/or Pull Type M12 Ш60 95 6 6 77 110 109 13 71 294 Dimensions given with armature in fully home position Dimensions given with armature in fully home position Direction of stroke Direction of stroke M12 Ш11,5 Ш100 19 30 110 M12 Ш60 95 6 6 65 Document LNSRM1/25 Revision 00 2 144 143 13 316 Ш100 Impulse Automation Limited United Kingdom Company Registration 665193 Information shown in these data sheets are for guidance purposes only, no liability is accepted for any errors or omissions.

The designer or user is solely responsible for the safe and proper use of these parts, assemblies or equipment described. without stroke limiter 109 M12 50+1 ~23 12 12 50+1 65 Ø76 Ø58 M 88 with stroke limiter 50+1 4 ~57 12 4 ~57 50+1 M1 1 2 156 Ø76 Ø58 M 19 30 110 88

Стр. 2

Email: sales@impulseautomation.co.uk Website: www.impulseautomation.co.uk RM100 Series Ordering Information 2) See below 3) Opposite to electrical connection 4) Same side as electrical connection 5) Available with stroke limit only 6) For plug-in socket 6.3 DIN 46247 and plug 200 +15 Z801 and Z811 Coil terminals N F Examples of design types: Direction of stroke Document LNSRM1/35 Revision 00 2 Impulse Automation Limited United Kingdom Company Registration 665193 Information shown in these data sheets are for guidance purposes only, no liability is accepted for any errors or omissions.

The designer or user is solely responsible for the safe and proper use of these parts, assemblies or equipment described. RM 100 – W – O R O R – N – 24 V DC 100 % ED Ord er specifications RM Line ar solenoid series 100 Des ign type ø mm W Hor izontal frontal force vs. stroke output Des cription2) O Stroke limit without H with R Plunger right hand side3) B both sides O Flange without R right hand side3) L left hand side4) O Gaiter without R right hand side3) L left hand side4) 5) B both sides5) F Coi l terminals Flying leads (20 cm standard length) N plug-in socket connection6) 24 Op erating voltage 24 V DC 205 205 V DC (connected to 230 V AC with SI- bridge rectifier) 100 % ED Per m.

duty cycle under air cooled conditions (LK) ca.12 ca.12

Стр. 3

Email: sales@impulseautomation.co.uk Website: www.impulseautomation.co.uk RM100 Series Accessories 41,0 10,0 Plug-in socket Z801 Screw joint PG 9 for lead diameter 4.5 - 7 mm 5,5 34,2 Plug-in socket Z811 Screw joint PG 11 for lead diameter 6 - 9 mm Plug-in socket with built in Si-bridge rectifier (30,5) Flange (Mounting screws are part of the shipment) ШJ ШG ШЕ ШF ШD Order specification C B H Document LNSRM1/45 Revision 00 2 Impulse Automation Limited United Kingdom Company Registration 665193 Information shown in these data sheets are for guidance purposes only, no liability is accepted for any errors or omissions.

The designer or user is solely responsible for the safe and proper use of these parts, assemblies or equipment described. Ø 19,0 ØI ØL K A ØI ØL K A ØL K Order Dimensio ns (mm) Dimensi ons (mm) Order number RMTy 0p9e 0 10A0,0 12B,0 17C,0 52D,0 43E,0 52F,0 9G0,5 H I J K L Type number Z 844 RM 100 110,0 13,0 19,0 58,0 49,0 58,0 100,5 1,0 11 ,5 8,4 88,0 76,0 RM 100 Z 844

Стр. 4