Downloaded from https://www.everyspec.com ... , Referring to table :51h.l-~.;.the:above identificat+on.sp?i~ies kthe.following,test=ie,; conditions: i.. ; ~J*t:,; :*iq#, :.,’.&.. ~+:q..,;, -.,-.,;> ~=~z+>.7 ., ,-s ~,- .....:/ ..-:.:,.-,- .:----- .. .. . . . .. Procedure 11,.+.“, ,~c ,--~~ .~,..,.., ,.-.+ - .,, Part 1 “- &tive phase (curveH) ,.~ :::!.,, - . . .. .//-,.-, Part.2- Plight phase (curve-R) ::: ...... -... Part 3 - Plight phase (curveAJ) ..:,-... Part 1 specifies a resonancesearch, resonance dwell, and sinusoidal cycling to the level of curve H from figure 51h.1-J within the time schedule specified for part 1 of procedure II on table 51b.1-IV.
These tests are followedby part 2, a sinusoidal cycling test to the level of curve R frcsnfigure 51b.l-k within the time schedule speci- fied for part 2 of procedureII on table 514.1-IV. Next, part 3, a random vibration .. test, shall be performed to the level of curve AJ from figure 51b.l-h within the time schedule specified for part 3 of procedure II on table 514.1-IV. b. Test rocedures.- The basis for selecting a test procedure (Procedure I ttiough X~cular equipment category shall be according to 3.
A procedure consists of all tests indiated‘oyan under the “Applicabletests” column of tables 515.1-1 through 51b.1-VIIto the right of the procedure number with the duration of the test as specified under the column entitled “Test time schedules (per axis)“. The vibra- tion environment, specifiedby the curve selected from tables 514.1-1 through 514.l-VII in accordance with 3, shallbe applied to each of the three mutually perpendicularaxes of the test item. The entire sequence of tests may be accomplishedfor any one axis before changing to the next axis. The transverse motion at the input monitoring point(s) shall be minimized,and should be limited to 100 percent of the input motion ....
except that reaction machines shall be balanced to reduce tr~sverse motion +/-10 percent. ,. 4,1 Test item’oper~ti% .- Unless otherwise specifie~~:the.test item.shall-~e operated during application of vibration (resonance se=ch, resonance dvell, cycling, and rendom vibration) so that functional effects caused by these tests may be evaluated, When a test item performemcetest is required during vibration and the time required for the performance test is greater.than the duration of the vibration test, the performance test shall be abbreviatedaccordingly.
Lt the conclusionof the”’test,the test item shall be operated and the results shall be compared with the data obtained in accordance with section 3, General’.Requ+qents, paragraph+3.2.1. ,At.rtheconclusionof each test, ...... the test item them shall:be.i+spected in accor~ce .@~-&t~on 3, General Requirements, ----- ~r~raph 3.2.k. :-.7... @a IY+z,, ;a -;.--? k.2 Mounting,tectiiqties.: - In accordance,,withsectici~3, @nera.1 Requireme?Jts, paragraph 3.2.2, the test item shall be attached to the vibrati6n exciter table by its normal mounti.ngmeans~.o-o,.by$.pe~s ofla rigid f.i@ure ca~b.le.-.of, transmittingthe vibra- tion conditions specifiedherein.
Precautions shall“betaken In the establishmentof. mechanical interfaces to minimize the introductionof mndeiirable responses in the test . ,.. ~.”~,,:,.: ..:. ~.::,’ “If.,.. .,:>, ,.!:;:-~~:+ c..r#;’&~ -.-;:;;.:;-- +. METHoy,:l~.1-;%.,, ~i$.”,, ;. . -:;;: . 511+.1-4 “*’.,.;:.: ~~ ,.‘.., ..,.,, ,. ... ;.. ,?.4,y.3;,,- :,,::, .-:. ,’;/:.:-..: .. ~....t, ., ::,$.:.. .....t.. &/&F: y .* ,,f.. ,0,-...-. 20 October 1969...‘,.~:” ‘,.: o::, .“.~~::.~.~, .;~.~ ,,,;.2;; ~~~~ ,.;~.:7.$. ,~.:.. ,,;;:,:.”” :,:J ..Y.,s: ., .?;,::~ ,: , .: ,.::;$: :-m-: ->.::$~= :;.+.,. ;,,,j,~:: . ...7>4.: , ~,~-:;::.s, ,:: .,.,, ..,.’>? ...-...Z :... .z~,w~,., .-. .:..., ,... . ....1 ,,..,..... ..;,,. ..- *.....1:
., .,:-.. ,’.~.,. ,>.:,7 v... ::!> ,,.;:, .. .. :;.;.:..,”,.:::+.. $y.,: p .,, ,: . -“.. :... + .’. ?!.-.” ..... ,,,,___ ,.,..3. . . .. .. . .. . ., ,.;., ... ,..;.- ,.7.’ ... . , J ~.. ,... -..,. .-.=,, ,’.. .+ ....1- . . ;.. ,.-y. ..->