Axis commissioning Axis dynamics On the dynamic tab for an axis, values for the acceleration , deceleration and jerk are to be set. Two methods are available: direct entry as a numerical value, or indirect specification via the run-up time and the characteristic acceleration curve. The values to be set here are the parameters to be observed by the set value generator. Drive manufacturers often mention values that would result in very hard axis positioning behavior if they were to be set here. This is because the values mentioned represent the limiting value of the motor's or of the power section. Usually, however, the machine's behavior would then be very dependent on the load.
The result of this is considerable variation in the following error, which causes the position controller to become active. However, the axis is hardly able to react to the controller output, because it is already operating at the limit of its current. The "correct" values for an axis depend heavily on the desired behavior and on the properties of the drive technology and of the machine. They can only be determined through test runs. Values should be tested as they are increased step by step, observing the following error when starting and stopping.
It has been found in practice that the numerical value for the jerk should be somewhere between twice (for processing axes) to ten times (for transfer axes) greater. For indirect adjustment, these correspond respectively to soft and hard adjustments. Use the values for the acceleration, deceleration and jerk from TwinCAT Scope for the adjustment. Whether the values for the acceleration A+ or deceleration A- are really achieved depends on the critical jerk J± , and on the ratio (A+)І/V or (A-)І/V , where V represents the set velocity. Check, in particular, whether the actual acceleration value can follow the set acceleration value (and the same for the deceleration).
The effects of incorrect cycle time settings Two errors result from incorrect cycle time settings, i.e. a difference between the set cycle time (NC task; SEC task; online; cycle ticks in ms) and the real cycle time taken by the SEC task: The set value generator information (position, velocity, acceleration) does not match the real cycle time, i.e. the velocity pre-control is incorrect. The position setpoints of the position controller and the set velocity values of the velocity pre-control are inconsistent. Velocity pre-control :
if the real cycle time TC_eff is greater than the set cycle time TC_saf the time axis becomes stretched out (scaling TC_eff/TC_saf ), and this implies a non-linear transformation of the setpoints. Every calculated set velocity is maintained ( TC_eff/TC_saf ) times longer than initially calculated. The integrated effective target velocity reaches a target position which is ( TC_eff/TC_saf ) times larger than the calculated one. Position control : since the target velocity and the set position do not match ( v(t) ≠ dp(t)/dt ), the position controller must work against the pre-control.
The resulting behavior depends on the proportionality factor, the size of the cycle time error setting, and the controller resources (reference velocity). In any event there will be a lag error in those phases where a force is present, and large overshoots. Delay between pre-control and position control The purpose of the delay generator is to compensate for the effects of a system-related delay time (hardware/communication) in the P part of an position controller between the output of the set velocity value and its effect on the positioning system.
Instead of the output velocity v_o(t) as a function of the velocity pre- control v_g(t) and of the P part K_v (p_g(t) - p_i(t)) , where p_g(t) is the position setpoint and p_i(t) is the actual position value, v_o(t) = v_g(t) + K_v ( p_g(t) - p_i(t)) + ... the position setpoint is output subject to a delay period of delta, so that v_o(t) = v_g(t) + K_v ( p_g(t-delta) - p_i(t))+ ... Parameter: delta delay time in s >= 0.0 Parameters for axis calibration These settings are only necessary for axes with incremental encoders . So that the actual value system in such axes can be adjusted to the machine's reference system, a calibration travel is started.
A number of parameters and signals are required for this. Numerical Control (NC) Basics 65 Version: 1.2